Connection Settings; Access Points; Access Point Groups; Packet Data - Nokia E62 Guide D'utilisation

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

S e t t i n g s
Speed dialling
— Select
keys (2-9), press and hold the key.
Anykey answer
— Select
Line in use
— Select
Line 1
setting is displayed only if the SIM card supports the alternate line service and a subscription to two phone lines.
Line change
— Select
Disable

Connection settings

Select
Menu
Tools
Settings
>
>

Access points

— Set up new or edit existing access points. Some or all access points may be preset for your device by your
service provider, and you may not be able to create, edit, or remove them.

Access point groups

— Set up new or edit existing access point groups that are used in automatic connection establishment
and e-mail roaming.

Packet data

— Determine when packet data connections are used, and enter the access point if you use your device as a
modem for a computer.
SIP settings
— View or create session initiation protocol (SIP) profiles.
Data call
— Set the time-out period after which data call connections automatically end.
VPN
— Install and manage VPN policies, manage VPN policy servers, view the VPN log, and create and manage VPN access
points.
Configs.
— View and delete trusted servers from which your device may receive configuration settings.
To obtain information about subscribing to a packet data service and the appropriate connection and configuration settings,
contact your network operator or service provider.
The settings available for editing may vary.
Access points
Select
Menu
Tools
Settings
>
>
Some or all access points may be preset for your device by your service provider, and you may not be able to create, edit, or
remove them.
See "Internet access points," p. 69.
Access point groups
Select
Menu
Tools
Settings
>
>
An access point group is used for grouping and prioritizing access points. An application can use a group as a connection method
instead of a single access point. The best available access point inside a group is used for making a connection.
To create an access point group, select
the group. In the
Conn. switching
Select and edit the access points that belong to this group in the
To add an access point to the selected access point group, select
to add.
To edit an access point in an access point group, select the access point and
To remove an access point in an access point group, select the access point and
To set the order in which access points are used for e-mail data roaming, select an access point group and Change. Select an
access point and
Options
Packet data
Select
Menu
Tools
Settings
>
>
Your device supports packet data connections, including GPRS in the GSM network. When you are using your device in a GSM
network, it is possible to have multiple data connections active at the same time; access points can share a data connection,
and data connections remain active during voice calls.

Packet data settings

The packet data settings affect all access points using a packet data connection.
Select from the following settings:
Packet data conn.
— Select
in a supported network. Select
it.
Copyright © 2006 Nokia. All Rights Reserved.
On
to activate speed dialing on your device. To dial a phone number assigned to the speed dialing
On
to answer an incoming call by briefly pressing any key, except the end key.
or
Line 2
to change the phone line for outgoing calls and text messages (network service). This
to prevent line selection (network service). To change this setting, you need the PIN2 code.
Connection
and from the following settings:
>
Connection
Access
>
>
Connection
Access point
>
>
Access point groups
field, define whether to show the connection switching process on the display of your device.
Raise priority
or
Lower
>
Connection
Packet
>
>
When available
to register the device to the packet data network when you switch the device on
When needed
to establish a packet data connection only when an application or action requires
points.
groups.
Options
New
>
>
Access points
Access points
priority.
data.
See "Connection manager," p. 66.
81
group. In the
Group name
section.
Options
Add access point
>
>
Options
> Edit.
Options
> Remove.
field, enter a name for
and the access point

Publicité

Chapitres

Table des Matières
loading

Table des Matières