Effect Section; Global Section - Numark OMNI CONTROL Guide D'utilisation Simplifié

9. PITCH - Each virtual deck features a PITCH
SLIDER, which can be used to change the pitch or
tempo of the music playing on the corresponding
deck.
10. PITCH BEND -/+ - You can use these two pitch
bend buttons to temporarily adjust the pitch and
tempo of the music playing on the corresponding
deck. Pitch bend is typically used to make small
adjustments when mixing two tracks so their beats
occur synchronously.
11. KEY - The KEY button engages the Key Lock
feature in Traktor LE. When Key Lock is engaged,
the pitch of the music playing on the deck will be
locked to the current value. You can then adjust
the tempo of the music, independent of the pitch.
12. SYNC - Press this button to synchronize the
tempo of the deck to the tempo of the other deck.
13. JOG WHEEL - When the deck is playing, rotating
the JOG WHEEL will temporarily bend the track's
pitch. When the deck is paused, rotating the JOG
WHEEL will scroll through the track's audio. You
can scratch with the JOG WHEEL if the deck's
SCRATCH button is engaged.
14. LOOP - Press this button to create a seamless
one bar loop. When you press the LOOP button,
the track will begin looping until you release the
loop by pressing the LOOP button again.
15. GAIN - Each virtual deck features a GAIN knob
which can be used to make adjustments to the
gain level on the corresponding deck.
16. EQ - Each deck features an EQ which can be
used to make adjustments to the levels of the
Treble, Mid, and Bass frequencies of the music.
By pressing down, each EQ knob can also
function as a Kill switch, removing that frequency
band from the music. The LED next to the knob
will light to let you know that the Kill feature has
been engaged. To disengage the Kill feature,
press on the knob again.
17. LOAD TRACK - Each virtual deck features a
LOAD TRACK button.
pressing the LOAD TRACK button will load the
track to the corresponding deck. You can "focus"
on one of the decks by holding down the PAGE
button and pressing the corresponding deck's
LOAD TRACK button.
Omni Control will only address the deck which is
currently "in focus".
18. CROSSFADER - You can use the CROSSFADER
to fade between the two tracks playing on the
virtual decks. If the crossfader is in the left-most
position, you will only hear the audio from deck A.
If the crossfader is in the middle position, you will
be able to hear both the audio from deck A and
the audio from deck B. If the crossfader is in the
right-most position, you will only be able to hear
the audio from deck B.
19. MASTER - The MASTER knob functions as
Master Level control, allowing you to change the
overall volume of the mix.
20. PH VOL - This knob adjusts the headphone mix
level. Please note that, unless you are using a
multiple output audio interface, the Monitor and
Master channels will be the same.
Selecting a track and
Certain controls on the
21. PH MIX - This knob adjusts the balance
between the Monitor and Master channels in
the headphones. Please note that, unless you
are using a multiple output audio interface, the
Monitor and Master Mix channels will be the
same.
22. PAN - This knob functions as the deck's
left/right balance control.
23. SCRATCH - Press and hold this button for
Scratch Mode.
activated, you can use the jog wheel to scratch
the audio playing on the deck.

EFFECT SECTION ::::

24. GAIN - This knob adjusts how much of the
selected effect will be mixed into the Master
Mix. In other words, if the knob is all the way
down, you will hear only the original sound.
Conversely, if the knob is all the way up, you
will hear only the effected sound.
25. SELECT - Press this button to select between
the different effects to be applied to the Master
Mix.
26. PAR 1 - This knob adjusts the first parameter
of the selected effect. Please note that this
parameter will be different, depending on which
effect you have selected.
27. ON/OFF - Press this button to turn the master
effect on and off.
28. PAR 2 - This knob adjusts the second
parameter of the selected effect, if available.
Please note that this parameter may be
different or unavailable, depending on which
effect you have selected.
29. DELAY TAP - This button can be used to
adjust a third parameter of the selected effect,
if available. For example, if you have selected
the Delay effect, you can use this button to tap
out the BPM of the Delay effect.

GLOBAL SECTION ::::

30. SEARCH/PLAY- This knob allows you to seek
through the preview player.
31. PREVIEW - Press this button to start and
pause the preview player.
32. SEARCH - This knob allows you to seek
through the music loaded on the deck which is
currently "in focus". You can focus on a deck
by holding down the PAGE button and
pressing
SOURCE button.
33. RELOOP - This button functions as a RELOOP
BUTTON. You can press this button to enter
the last set loop.
previously set, pressing RELOOP will begin
looping the first bar of the track.
34. FINE PITCH - This button allows you to make
fine pitch adjustments to the music on the deck
which is currently "in focus". You can focus on
a deck by holding down the PAGE button and
pressing
SOURCE button.
35. SYNC - This button allows you to synchronize
the downbeats of the music playing on the
deck currently "in focus" to the downbeats of
the other deck. You can focus on a deck by
holding down the PAGE button and pressing
the corresponding deck's CUE SOURCE
button.
10
While Scratch Mode is
the corresponding deck's
If no loop has been
the corresponding deck's
CUE
CUE