Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
Features
1. On/off switch
2. Lock-on button
3. Dust bag
4. Dust extraction outlet
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting a sanding belt (fig. A)
Warning! Never use the tool without a sanding belt (6).
Pull the tension lever (5) outward to release the tension
on the sanding belt (6).
Remove the old sanding belt (6).
Place a new sanding belt (6) over the rollers. Ensure
that the arrow on the sanding belt (6) points in the same
direction as the arrow on the tool.
To ensure a correct tracking, the sanding belt (6) must
be centred over the rollers.
Push the tension lever (5) inward to tension the sanding
belt (6).
Fitting and removing the dustbag (fig. B)
Slide the dustbag (3) over the dust extraction outlet (4).
To remove the dustbag (3), slide it off the outlet.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These include:
Injuries caused by touching any rotating/moving parts.
Injuries caused when changing any parts, blades or
accessories.
Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods make sure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF).
Use
Warning! Let the tool work at its own pace. Do not overload.
The auto tracking feature of this sander allows you to sand
without adjusting the location of the sanding belt (6).
Make sure that the sanding belt (6) is centred over the
rollers during assembly.
6
During use, if the sanding belt (6) begins to track
incorrectly, remove the belt sander from the work piece
and allow it to run briefly. The sanding belt (6) will return
to its centred position.
If the sanding belt (6) does not return to the centred
position, allow the unit to cool for 5 minutes and repeat.
Switching on and off (fig. D)
To switch the tool on, press the on/off switch (1).
For continuous operation, press the lock-on button (2)
and release the on/off switch (1).
To switch the tool off, release the on/off switch (1).
To switch the tool off when in continuous operation,
press the on/off switch (1) once more and release it.
Emptying the dustbag
The dustbag (3) should be emptied every 10 minutes.
Unzip the dustbag (3) and empty it before continuing.
Hints for optimum use
Always hold the tool with both hands (fig. C).
Do not exert too much pressure on the tool.
Regularly check the condition of the sanding belt (6).
Replace when necessary.
Always sand with the grain of the wood.
When sanding new layers of paint before applying
another layer, use extra fine grit.
On very uneven surfaces, or when removing layers of
paint, start with a coarse grit. On other surfaces, start
with a medium grit. In both cases, gradually change to a
fine grit for a smooth finish.
Consult your retailer for more information on available
accessories.
Accessories
The performance of your tool depends on the accessory
used. Black & Decker and Piranha accessories are
engineered to high quality standards and designed to
enhance the performance of your tool. By using these
accessories you will get the very best from your tool.
Maintenance
Your Black & Decker tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Warning! Before performing any maintenance, switch off
and unplug the tool.
Regularly clean the ventilation slots in your tool using a
soft dry brush or dry cloth.
Regularly clean the motor housing using a clean damp
cloth. Do not use any abrasive or solvent-based
cleaner.
Publicité
Table des Matières
