Wahl MOSER ermila 1565 Q Traduction Du Mode D'emploi D'origine page 14

E N G L I S H
Maintenance
Warning! Injuries and material damage due to incorrect
handling.
f Switch off the hair clipper before cleaning it or perform-
ing any maintenance and disconnect it from the mains.
Cleaning and care
Danger! Electric shock due to penetration of liquid.
de
f Do not immerse the hair clipper in water!
f Do not allow any liquid to get inside the appliance.
en
f Only reconnect the appliance to the power supply if it is
completely dry.
fr
Caution! Danger from aggressive chemicals.
it
Aggressive chemicals could damage the appliance and
accessories.
es
f Never use solvents or scouring agents.
f Only use cleaning agents and blade set oil recom-
pt
mended by the manufacturer.
nl
Accessories and spare parts are available from your dealer or
da
our service centre.
sv
f Remove the attachment comb (Fig. 4ⓑ) after every use and lift
the blade set out of the housing (Fig. 5ⓐ). Use the cleaning brush
no
to remove any cut hairs from the housing opening and from the
blade set (Fig. 6). The cleaning lever can also be pressed. This allows
fi
the cut hairs that accumulate between the bottom blade and the
top blade to be easily removed using the cleaning brush(EASY
tr
CLEANING).
f Always keep the appliance socket (D) clean.
pl
f Only wipe the hair clipper with a soft, slightly damp cloth.
cs
f The blade set using the hygienic spray.
f Oil the blade set with the blade set oil (Fig. 7).
sk
f For a good and long-lasting cutting performance, it is
hr
important to oil the blade set frequently.
f If the cutting performance deteriorates after long use
hu
despite regular cleaning and oiling, the blade set should
be replaced.
sl
Changing the blade set
ro
1. Slide the blade set off the housing in the direction of the arrow
bg
(Fig. 5ⓐ). Remove the blade set.
2. Replace the blade set by hooking it into the housing and pressing it
ru
down until it clicks into position (Fig. 5ⓑ).
uk
et
lv
lt
el
14
ar
Problem elimination
Blade set is cutting badly.
Blade set is pulling hair out.
Battery operating time is too short.
Cause: Blade set is dirty or worn out.
f Clean and oil the blade set (Fig. 6/7). If this does not resolve the
problem, replace the blade set (Fig. 5).
Skin injury
Cause: Too much pressure on the skin.
f Reduce pressure when cutting close to skin.
Cause: Cutting angle is too steep.
f Hold the hair clipper flatter to the skin.
Charging indicator light does not light up.
Cause: appliance socket is dirty.
f Clean appliance socket (D).
Cause: Defective power supply.
f Make sure that there is a faultless contact between the plug-in
transformer and the socket. Check the mains cable for possible
damage.
In the event that this information does not help you resolve your prob-
lem, please contact our service centre. Never attempt to repair the hair
clipper yourself!
Disposal
Handle with care! Environmental damage in the event of
incorrect disposal.
f Discharge batteries prior to disposal!
f Correct disposal will ensure environmental protection
and prevent any potentially harmful impact on people
and the environment.
Adhere to the relevant legal requirements when disposing of the
appliance.
Information on the disposal of electrical and electronic appli-
ances in the European Community:
Within the European Community, national regulations are
specified for the disposal of electrical appliances, based
on EU Waste Electrical and Electronic Equipment Directive
2012/19/EC (WEEE). In accordance with this, the appliance
can no longer be disposed of with the local or domestic
waste.The appliance will be accepted free of charge by local
collection points or recycling centres. The packaging for this
product is made from recyclable materials. Dispose of this in
an environmentally friendly manner by recycling it.