Cautions And Warnings; Before Installing The Washlet - Toto Washlet GL TCF891G Guide D'installation

GB GB

Cautions and warnings

Cautions and warnings
Before installing your Washlet, be sure to read the following installation instructions. Install the product only as Before installing your Washlet, be sure to read the following installation instructions. Install the product only as
described in this guide. described in this guide.
Follow all safety precautions and warnings. Follow all safety precautions and warnings.
When this appears next to a topic, When this appears next to a topic,
this indicates that misoperation this indicates that misoperation
could result in death or serious could result in death or serious
WARNING WARNING
injury. injury.
Symbol example Symbol example
The The symbol indicates symbol indicates
something that is prohibited. something that is prohibited.
This equipment is Class 1, so it is necessary to attach it to an earthed connection. This equipment is Class 1, so it is necessary to attach it to an earthed connection.
Install this equipment close to a mains socket. Install this equipment close to a mains socket.
Use the new hose set included with this equipment. Do not reuse an old hose set. Use the new hose set included with this equipment. Do not reuse an old hose set.
Since this is electronic equipment, do not locate it in a place where it might be splashed or Since this is electronic equipment, do not locate it in a place where it might be splashed or
otherwise become wet. Likewise, do not locate it in a humid place where water could drip onto otherwise become wet. Likewise, do not locate it in a humid place where water could drip onto
the surface of the Washlet. When using it in a bathroom, install a ventilation fan or ventilation the surface of the Washlet. When using it in a bathroom, install a ventilation fan or ventilation
opening, so that the bathroom has suf cient air ow. opening, so that the bathroom has suf cient air ow.
Install the Washlet at least 0.6 m away from any bathtub. Install the Washlet at least 0.6 m away from any bathtub.
(Failure to observe this caution may result in re or electrical shock.) (Failure to observe this caution may result in re or electrical shock.)
Prepare the socket for the electrical wiring as follows. Prepare the socket for the electrical wiring as follows.
(Failure to observe this caution may result in re or electrical shock.) (Failure to observe this caution may result in re or electrical shock.)
a. Provide electric current to the socket (device) using a differential residual electric current a. Provide electric current to the socket (device) using a differential residual electric current
device (DDR) with a released current that does not exceed 30 mA. device (DDR) with a released current that does not exceed 30 mA.
b. Locate the socket (device) and its wiring plug at least 0.6 m from the outside edge of a b. Locate the socket (device) and its wiring plug at least 0.6 m from the outside edge of a
shower chamber or bathtub. shower chamber or bathtub.
Con rm that the wiring for items a and b above has been completed. If the wiring has not Con rm that the wiring for items a and b above has been completed. If the wiring has not
been completed, request completion from the business that installed the unit. been completed, request completion from the business that installed the unit.
Be sure to install an earth wire in a place where connection is ensured. Be sure to install an earth wire in a place where connection is ensured.
(If the earth wire is not installed, electric shocks (If the earth wire is not installed, electric shocks
could occur if there is a malfunction or a short could occur if there is a malfunction or a short
Required Required
circuit.) circuit.)
Note: Note:
Use copper wire with a diameter of 1.6 mm or Use copper wire with a diameter of 1.6 mm or
more and with an earth resistance of 100 more and with an earth resistance of 100
less. less.
If the earth wire has not been installed, request If the earth wire has not been installed, request
installation from the business that installed the installation from the business that installed the
unit. unit.
Always insert the electrical cord completely into the socket (220-240 V AC, 50 Hz). Always insert the electrical cord completely into the socket (220-240 V AC, 50 Hz).
(Failure to observe this caution may result in re or electrical shock.) (Failure to observe this caution may result in re or electrical shock.)
Make the connection so that the electrical plug is easy to reach. Make the connection so that the electrical plug is easy to reach.
Always connect the Washlet to the cold water supply. Always connect the Washlet to the cold water supply.
(Failure to do so could cause burns or malfunction of the equipment.) (Failure to do so could cause burns or malfunction of the equipment.)
Follow the installation requirements for the country in which the Washlet is being installed. Follow the installation requirements for the country in which the Washlet is being installed.
Use only tap water or potable well water (groundwater). Use only tap water or potable well water (groundwater).
(Use of other water could cause skin in ammation or other problems.) (Use of other water could cause skin in ammation or other problems.)
Do not use this product with any power supply other than speci ed (220-240 V AC, 50 Hz). Do not use this product with any power supply other than speci ed (220-240 V AC, 50 Hz).
Prohibited Prohibited
(Failure to observe this caution may result in re or electrical shock.) (Failure to observe this caution may result in re or electrical shock.)
2 2
When this appears next to a topic, When this appears next to a topic,
this indicates that misoperation may this indicates that misoperation may
CAUTION CAUTION result in injury or physical damage. result in injury or physical damage.
The The symbol indicates something symbol indicates something
that must be done. that must be done.
WARNING WARNING
Ventilation fan or ventilation opening Ventilation fan or ventilation opening
Circuit board Circuit board
or or
0.60 m 0.60 m
Earth leakage Earth leakage
breaker breaker
0.60 m 0.60 m
After cleaning the water lter, thoroughly tighten the drain valve with built-in water lter. After cleaning the water lter, thoroughly tighten the drain valve with built-in water lter.
(Failure to do so could cause a water leak.) (Failure to do so could cause a water leak.)
Follow the Installation Guide thoroughly during installation. Follow the Installation Guide thoroughly during installation.
Required Required
(Failure to attach things correctly could cause water leaks.) (Failure to attach things correctly could cause water leaks.)
Do not detach the drain valve with built-in water lter while the water shut-off valve is still open. Do not detach the drain valve with built-in water lter while the water shut-off valve is still open.
(Doing so will cause water to spill.) (Doing so will cause water to spill.)
Do not bend or crush the water supply hose. Do not bend or crush the water supply hose.
(This could cause a water leak.) (This could cause a water leak.)
Prohibited Prohibited
Do not lift the Washlet by the seat or toilet lid. Do not lift the Washlet by the seat or toilet lid.
(Injury could result if the main Washlet unit becomes dislodged and falls.) (Injury could result if the main Washlet unit becomes dislodged and falls.)

Before Installing the Washlet

Before Installing the Washlet
1. Do not transmit electrical current or supply water to the unit until the installation process is complete. 1. Do not transmit electrical current or supply water to the unit until the installation process is complete.
2. Do not damage the connected parts at the end of the water supply hose. 2. Do not damage the connected parts at the end of the water supply hose.
3. The power voltage is 220-240 V AC (50 Hz). The rated energy consumption is 270-320 W. Use wiring and 3. The power voltage is 220-240 V AC (50 Hz). The rated energy consumption is 270-320 W. Use wiring and
electrical sockets that are appropriate for this level of power. (Independent wiring is recommended.) electrical sockets that are appropriate for this level of power. (Independent wiring is recommended.)
4. Do not install the base plate to the Washlet when it is not attached to the toilet. (Turning the Washlet on in this 4. Do not install the base plate to the Washlet when it is not attached to the toilet. (Turning the Washlet on in this
condition could result in product damage.) condition could result in product damage.)
5. The power cord is about 0.9 m long. Con rm that a mains socket is installed within reach to allow easy 5. The power cord is about 0.9 m long. Con rm that a mains socket is installed within reach to allow easy
installation and removal of the Washlet. installation and removal of the Washlet.
6. Use a water supply with pressure between 0.1 - 1.0 Mpa. 6. Use a water supply with pressure between 0.1 - 1.0 Mpa.
7. The water temperature range should be between 0 - 35°C. 7. The water temperature range should be between 0 - 35°C.
8. The length of the connection hose is 0.5 m. The water supply should be located to allow easy installation and 8. The length of the connection hose is 0.5 m. The water supply should be located to allow easy installation and
removal of the Washlet. removal of the Washlet.
9. Before installing the Washlet, con rm that the water supply is on a regulated position. 9. Before installing the Washlet, con rm that the water supply is on a regulated position.
CAUTION CAUTION
GB GB
3 3