Taurus LIQUAJUICE PRO Mode D'emploi page 10

Attention:
If the auger (C) is not fully inserted, the cover will
not close properly. Make sure the auger is well
placed, turning and pressing down
- If feeding tube is not well closed, device won't
operate properly.
Use
- Wash the fruit and /or vegetable and cut them
into pieces that fit into the feeding tube.
- Please make sure that the switch is turned at
"O" before to connect to the power.
- Connect the appliance to the mains.
- Put the juicer cup and residue cup under the
juice and dregs spout
- The switch has 3 positions: (Fig 1)
ON- starts the machine and juicing process
STOP- is the central position of the button. It
stops the appliance
REV- is REVERSE. It is a function to be used
when something is stuck in the juicer and it
needs to be unclogged. Finger should keep
pressing this button while it start working.
- Prepare the material you wish to juice. The
slow juicer is designed to juice many different
materials
-T he necessary preparation will be different
depending on the used materials
- If you use small mouth juicing, ensure juice
material is cut small portion for optimal juice
extraction
- Each portion should easily fall down the hopper
chute without the need for force
-I f big mouth juicing, ensure the diameter of the
fruit is less than 5.5 cm
- Turn the appliance on, by turning the control
knob to setting "ON"
- Insert pre- cut pieces slowly in the feeding tube
and allow juicer have time to work.
- Don't overstuff the hopper or force food in
- Only use the aid of the pusher when necessary
- Remark: If you process a large quantity of fruit,
you must periodically clean the filter and remove
the remains of the pulp.
Safety thermal protector:
- The appliance has a safety device, which pro-
tects the appliance from overheating.
- If the appliance turns itself off and does not
switch itself on again, disconnect it from the
mains supply, and wait for approximately 15
minutes before reconnecting. If the machine
does not start again seek authorised technical
assistance.
NOTES:
- This product is only used for extract juice.
- Peel only the ingredients with thick skin such as
citrus fruits, bananas, pineapples, melon and
so on.)
-Remove the kernel from the fruits such as plums,
peaches, cherries, apricots and so on)
- Other fruit with soft peel should be washed be-
fore extracting such as apples, carrots, grapes,
strawberry and so on.)
- Never put fruit kernel, excessively hard foods
(ice cubes, sugar cubes), extremely fibrous food
or meat into your juicer because they would
damage the filter net and pusher.
-Switch "ON" stand for rotating clockwise, switch
R stands for rotating reversely, switch "O"
stands for stop. When there is some fruits be
stuck between filter net and pusher, please turn
the switch to speed "R" to make the fruit exit,
then turn the switch to ON for extracting.
- Slowly put the fruit into the feeding chute slowly,
leaving the appliance to work
- Only use pusher assistance when necessary
NOTES:
- Please do not put your fingers or other objects
to the feeding chute is blocked, please use the
pusher or other fruit slice to push and remove
the stuck fruit. If it still won´t work, stop the
machine and clean up the stuck fruit.
- Turn the switch to "O" if the juice cup or dregs is
full, please also turn off the machine if there is
no fruit. Empty the cup and clean the filter net
and feeding chute for the next extracting.
Once you have finished using the appliance:
- Turn the appliance off, using the on/off switch.
- Unplug the appliance from the mains.
- Clean the appliance.
How to disassemble and clean the unit
- Switch off the unit
- Unplug the appliance from the mains.
- Twist the hopper anticlockwise then lift off. Lift
the bowl straight up to remove from the base
- Disassemble the parts from the juicing bowl in
the following order:
- Auger (C), Filter (D1), Spinning brush (D2),
Juice bowl (E)