Electrical Safety - Black & Decker BDCCS18 Mode D'emploi

ENGLISH
Warning!
The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following pictograms are shown on the tool along with the
date code:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Additional safety instructions for batteries and
chargers (may not be included)
Batteries (may not be included)
Never attempt to open for any reason.
u
Do not expose the battery to water.
u
Do not store in locations where the temperature may
u
exceed 40 °C.
Charge only at ambient temperatures between 10 °C and
u
40 °C.
Charge only using the charger provided with the tool.
u
When disposing of batteries, follow the instructions given
u
in the section "Protecting the environment".
Chargers (may not be included)
Use your BLACK+DECKER charger only to charge the
u
battery in the tool with which it was supplied. Other batter-
ies could burst, causing personal injury and damage.
Never attempt to charge non-rechargeable batteries.
u
Have defective cords replaced immediately.
u
Do not expose the charger to water.
u
Do not open the charger.
u
$
Do not probe the charger.
u
The charger is intended for indoor use only.
Read the instruction manual before use.

Electrical safety

#
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on the
rating plate. Never attempt to replace the charger
unit with a regular mains plug.
8
(Original instructions)
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKER Centre
in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Main handle
2. Lock-off button
3. On/Off trigger
4. Battery (may not be included)
5. Shoe
6. Depth adjustment knob
7. Secondary handle
8. Upper Guard
9. Bevel adjustment scale
10. Blade
11. Lower blade guard
12. Depth adjustment scale
13. Locking tool
14. Dust extraction port
15. Bevel adjustment knob
16. Spindle lock
Charging procedure (may not be included)
BLACK+DECKER chargers are designed to charge
BLACK+DECKER battery packs.
Plug the charger into an appropriate outlet before inserting
u
the battery pack.
Insert the battery pack into the charger.
u
The green LED will flash indicating that the battery is
u
being charged.
The completion of charge is indicated by the green LED
u
remaining on continuously. The pack is fully charged and
may be used at this time or left on the charger.
Note: Recharge discharged batteries as soon as possible
after use or battery life may be greatly diminished. For longest
battery life, do not discharge batteries fully.
It is recommended that the batteries be recharged after each
use.
Leaving the battery in the charger (may not be
included)
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
Important charging notes (may not be included)
Longest life and best performance can be obtained if
u
the battery pack is charged when the air temperature is
between 65°F and 75°F (18°- 24°C). DO NOT charge the
battery pack in an air temperature below +40°F (+4.5°C),
or above +105°F (+40.5°C). This is important and will
prevent serious damage to the battery pack.