Troubleshooting Guide - Kenwood KAC-X1R Mode D'emploi

Troubleshooting Guide

What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following
table for possible problems.
PROBLEM
No sound.
(Blown fuse.)
The output level is too small
(or too large).
The sound quality is bad.
(The sound is distorted.)
The Remote Controller does
not function.
Specifications
Specifications subject to change without notice.
CEA-2006
RMS Watts per channel @ 4 ohms, 1 % THD+N .......................................................................................................................................................................600 W × 1
Signal to Noise Ratio (Reference: 1Watt into 4 ohms) ................................................................................................................................................................ 80 dBA
Audio Section
Max Power Output .........................................................................................................................................................................................................................................2400 W
Rated Power Output (+B = 12.0 V)
(4 Ω) (20 Hz – 200 Hz, 0.5 % THD) .....................................................................................................................................................................................400 W × 1
(2 Ω) (100 Hz, 0.5 % THD) .......................................................................................................................................................................................................800 W × 1
(1 Ω).............................................................................................................................................................................................................................................. ≥ 800 W × 1
Rated Power Output (+B = 14.4 V)
(4 Ω) (20 Hz – 200 Hz, 0.5 % THD) .....................................................................................................................................................................................600 W × 1
(4 Ω) (DIN45324, +B = 14.4 V) .............................................................................................................................................................................................600 W × 1
(2 Ω) (100 Hz, 0.5 % THD) .................................................................................................................................................................................................... 1200 W × 1
(1 Ω)........................................................................................................................................................................................................................................... ≥ 1000 W × 1
Frequency Response (+0, –3 dB) ..............................................................................................................................................................................................5 Hz – 400 Hz
Sensitivity (rated output) (MAX.) .................................................................................................................................................................................................................0.2 V
Sensitivity (rated output) (MIN.) ..................................................................................................................................................................................................................5.0 V
Input Impedance ............................................................................................................................................................................................................................................... 10 kΩ
Signal to Noise Ratio ......................................................................................................................................................................................................................................105 dB
Low Pass Filter Frequency (–24 dB/oct.) ..............................................................................................................................................................40 – 200 Hz (variable)
Infrasonic Filter Frequency (–24 dB/oct.) .............................................................................................................................................................. 15 – 60 Hz (variable)
Band Reject Filter ...................................................................................................................................................................................................................OFF/ -6 dB/ -12 dB
Band Reject Filter Frequency .................................................................................................................................................................................... 40 – 200 Hz (variable)
Phase Inverter ...................................................................................................................................................................................................... 0° (Normal) / 180° (Reverse)
Bass Boost Circuit ..................................................................................................................................................................................................................0 – 18 dB (variable)
Bass Boost Frequency ....................................................................................................................................................................................................40 – 100 Hz (variable)
Bass Boost Frequency ...................................................................................................................................................................................................................................................
General
Operating Voltage .............................................................................................................................................................................................. 14.4 V (11 – 16 V allowable)
Current Consumption ........................................................................................................................................................................................................................................ 75 A
Installation Size (W × H × D) .........................................................................................................................................................................................340 × 60 × 225 mm
..................................................................................................................................................................................................................1213-3/8 × 2-3/8 × 8-7/8 inch
Weight ................................................................................................................................................................................................................................................3.8 kg (8.38 lbs)
Weight ..................................................................................................................................................................................................................................................................................
8 English
POSSIBLE CAUSE
• Input (or output) cables are disconnected.
• Protection circuit may be activated.
• Volume is too high.
• The speaker cord is shorted.
• The input sensitivity adjusting control is not set to the correct
position.
• The speakers wire are connected with wrong + /-polarity.
• A speaker wire is pinched by a screw in the car body.
• The switches may be set improperly.
• The Remote Cable is disconnected.
SOLUTION
• Connect the input (or output) cables.
• Check connections by referring to <Protection function>.
• Replace the fuse and use lower volume.
• After check the speaker cord and fixing the cause of the short,
replace the fuse.
• Adjust the control correctly referring to <Controls>.
• Connect them properly checking the + / - of the terminals
and wires well.
• Connect the speaker wire again so that it is not pinched by
anything.
• Set switches properly by referring to <Controls>.
• Connect the Remote Cable securely and correctly.