Battery Charge Indicator; Starting Operation - Bosch GNH 18V-64 Professional Notice Originale

20 | English

Battery charge indicator

The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator or
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Battery model GBA 18V...
LEDs
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Battery model ProCORE18V...
LEDs
5× continuous green light
4× continuous green light
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Loading the magazine (see figures A1–A4)
Remove the rechargeable battery before adjusting the
u
tool settings, changing accessories, or storing the
power tool. This safety measure prevents the power tool
from being started accidentally.
Use only original Bosch accessories. The precision parts of
the power tool, such as the magazine, the outlet and the shot
duct, are matched to Bosch staples, nails and brads. Other
manufacturers use different steel grades and sizes.
Using unapproved fasteners can damage the power tool and
cause injuries.
While loading the magazine, hold the power tool in such a
manner that the outlet (15) is not pointed at your body or at
other persons.
– Clean the magazine slider (13) as required and make sure
that the magazine (12) is not contaminated.
– Insert a suitable nail strip (16) in the T-slot at the end of
the magazine (12).
1 609 92A 5TX | (10.05.2021)
– Push the nail strip forwards in the magazine until the last
nail is positioned in front of the magazine spring (17).
Note: A lock function of the magazine slider prevents the
power tool from being started with an empty magazine. The
discharge lock-off cannot be pressed down and blank firing
is thus prevented.
to
– Press the pretensioned nail pusher (14) against the
magazine slider (13) and, at the same time, pull the
magazine slider completely to the end of the
magazine (12).
Note: The magazine slider must slide back with only low
force (finger-pressure). A tight-running magazine slider
causes the nails to be driven in at an incorrect angle.
– With the nail pusher (13) pressed, carefully guide the
magazine slider (14) forwards until the nail pusher is over
the last nail, thus pushing the nail strip in the magazine
Capacity
completely to the front.
60−100 % Note: Do not let the magazine slider snap back without guid-
ing it. This could damage the magazine slider and there is a
30−60 %
risk of getting your fingers caught.
5−30 %
0−5 %
Operation
Actuation systems
Single actuation with safety run
With this actuation system, the discharge lock-off (2) must
first be firmly pressed against the workpiece. A fastener is
Capacity
not discharged until the trigger (5) is pulled.
80−100 % Afterwards, further discharging procedures can only be ac-
tuated when the trigger and the discharge lock-off have been
60−80 %
set back to the starting position.
40−60 %
Contact actuation with automatic return
20−40 %
(GNH 18V-64 M)
5−20 %
With this actuation system, the trigger (5) must be pulled
0−5 %
first and held in this position. Afterwards, the discharge
lock-off must be firmly pressed against the workpiece in or-
der to discharge the fastener. (5)Further discharging pro-
cedures can be actuated by repositioning it elsewhere, while
the trigger is pushed.
In contact actuation mode, a nail can also be driven in with
single actuation.

Starting Operation

Remove the rechargeable battery before adjusting the
u
tool settings, changing accessories, or storing the
power tool. This safety measure prevents the power tool
from being started accidentally.
Inserting the Battery
– Push the charged battery (7) into the battery bay of the
power tool until the battery is securely locked.
Switching On and Off (see figure B1B2)
– To switch on the power tool, press the on/off switch
button (18) for at least 1 second.
The on/off switch display (19) lights up green.
Bosch Power Tools