Indicator Lights - Honeywell HEV615 Serie Manuel D'instructions

USING YOUR HUMIDIFIER – HEV615
HEV615 Push Button Control
Key
C
A. Power
D
B. Moisture Output
B
C. Humidity Control E
D. Check Filter
E. Humidity Reached
F. Refill
Power
1. Plug humidifier into a 120V outlet.
CAUTION:
to avoid electric shock, DO NOT plug humidifier into outlet with wet hands.
2. Press Power button (A).
Humidifier will turn on to high output and high humidity settings. Press again to turn off.
If humidifier was programmed before turning off, previous settings will be remembered.
Unplugging the humidifier resets to default settings.
Moisture Output
3. Press the Moisture Output buttons
level accordingly.
A higher setting will provide more moisture output. The fan will pull more moisture off the
Wicking Filter and into the air. The water level in the Water Tank will decrease faster with a
higher setting, since more moisture is going into the air.
A lower setting will provide less moisture output. The fan will run quieter, and the Water Tank
will not have to be filled as frequently, since less moisture is going into the air
Humidity Control
4. Press the Humidity Control buttons
It is recommended to run the humidifier on the highest humidity level for at least an hour,
or until a comfortable humidity level is reached.
Then adjust the Humidity Control button down until the Humidity Reached Indicator light
illuminates and the humidifier turns off. This is your desired humidity level. The humidifier
will turn on and off to maintain this setting.
Humidity Reached
When the set humidity level is reached, the blue Humidity Reached indicator (E) will
illuminate, and the humidifier will turn off. As long as this light is illuminated, the fan
will not run. Once the humidity level drops below the set humidity level, the blue light will
turn off, and the humidifier will start running again. To increase the set humidity level,
press the button.
Symbols
C
D. Check
Filter
B
E. Humidity
F
Reached
A
F. Refill
or (B) to adjust the moisture output
or (C) to set the desired humidity level.
8

INDICATOR LIGHTS

Refill
When the Water Tank is empty, the humidifier will automatically shut off and the orange Refill
Indicator (F) will illuminate. Turn off the humidifier and refill the Tank.
See Filling/Refilling Water Tank on previous pages.
(Canada only)
NOTE: If the humidifier will not be used for more than a few days, empty the water from the
Water Tank and Water Reservoir and dry out the Filter to prevent growth of bacteria or mold.
Check Filter
After 30 days the orange Check Filter indicator will illuminate to remind you to check your
Wicking Filter. Remove the Filter Cartridge from the back of the humidifier, and check to see
if it needs to be replaced. To reset this light, press and hold the Check Filter button for 2
seconds. If humidifier is unplugged, the 30 day counter will start over.
CARING FOR YOUR FILTER
To remove the filter
CAUTION:
drain before removing. This will help prevent dripping on your floor or other surfaces.
Step 1
1. Pull the Filter Cartridge Handle straight up slowly, listening for water dripping from the filter.
2. With the Cartridge fully removed, flip the Cartridge Door open.
3. Remove the filter, and either:
a. Flip top to bottom to ensure the top does not dry out OR b. Replace with a new filter.
To prolong the life of your Wicking Filter, turn it over each time you fill the Water Tank.
This will keep the top of the Filter from drying out and will help the Filter to age more evenly.
If you notice the Filter getting hard, you may soak it in cool water to loosen mineral buildup.
This will temporarily improve performance of the Wicking Filter until a replacement Filter is purchased.
DO NOT attempt to clean the Wicking Filter with vinegar, soap or any chemical solutions.
Doing so may damage the Filter.
It is recommended you change your Wicking Filter every 30-60 days depending on water
quality and usage. If you have hard water, you may need to replace your Filter more frequently.
Change your Filter if you notice:
• The Filter is hard and crusty
• The Filter starts to give off an odor
• Moisture output is decreased
(ALL MODELS)
Filter may be saturated with water. Remove slowly to give filter time to
Step 3a
Step 2
Lift
Slowly
9