Cleaning, Care And Maintenance - Elcalor SH 2020 Utilisation Et Installation

Operation
Time programs Pro1 and Pro2
You can specify the comfort mode start and end times
with time programs Pro1 and Pro2. During this time pe-
riod, the appliance heats to the set comfort temperature.
Outside this specified time period, the appliance operates
in setback mode. This results in a comfort phase and
a setback phase, which are repeated daily (Pro1) or on
every working day (Pro2).
Theses phases are factory-set as follows:
◦ 08:00 h - 22:00 h: Comfort mode
◦ 22:00 h - 08:00 h: Setback mode
Note
When time program Pro2 is enabled, the appliance
operates at weekends exclusively in setback mode.
To adapt time programs Pro1 and Pro2 according to your
needs, proceed as follows:
» In the configuration menu, use "+" and "–" to call up
the required time program.
» Press "OK".
The start time for comfort mode is displayed.
» Use "+" and "–" to set the required start time.
» Press "OK".
The end time for comfort mode is displayed.
» Use "+" and "–" to set the required end time.
» Press "OK" to save.
Time program Pro3
You can use time program Pro3 to specify up to 14 sepa-
rate comfort phases which are repeated weekly.
To configure a comfort phase in time program Pro3, pro-
ceed as follows:
» In the configuration menu, use "+" and "–" to call up
time program Pro3.
» Press "OK".
The display shows "3---".
» Press "OK".
A day of the week or a group of days is displayed.
» Use "+" and "–" to select the required day or group
of days.
» Press "OK".
The start time for comfort mode is displayed.
» Use "+" and "–" to set the required start time.
» Press "OK".
The end time for comfort mode is displayed.
» Use "+" and "–" to set the required end time.
» Press "OK".
Comfort phase "3-01" has been configured.
» To configure a further comfort phase, use "+" and
"–" in time program Pro3 to select display "3---". Pro-
ceed as describe above.
Note
To reset the selected comfort phases, activate pa-
rameter P4.
» Please note that activating parameter P4 resets
all time programs (Pro1, Pro2, Pro3) to the facto-
ry setting.
40
5.4.3 Parameter
You can call up the following parameters:
Display Description
P1 Room temperature offset
P2 Time format
P3 Temperature display units
P4 Reset the time programs (Pro1, Pro2, Pro3)
P5 Reset relative heating time
To change the value of a parameter, use "+" and "–" to
call up the relevant parameter. Press "OK".
As soon as the "Editable parameter" symbol appears, you
can change the parameter value with "+" and "–". Press
"OK" to save the selected value.
P1: Room temperature offset
Uneven temperature distribution in the room can result in
a difference between displayed actual temperature I1 and
the room temperature you measure. To compensate for
this difference, a room temperature offset of ±3 °C can
be set via parameter P1.
Example: The appliance indicates I1 = 21.0 °C. You have
measured a room temperature of 20.0 °C. There is a dif-
ference of 1.0 °C.
» To compensate for the difference, select an offset of
P1 = -1.0.
P2: Time format
Parameter P2 allows you to specify whether the time is
displayed in the 12 hour or 24 hour format.
P3: Temperature display units
Parameter P3 is used to specify whether the room tem-
perature is displayed in degrees Centigrade [°C] or Fahr-
enheit [°F].
P4: Reset time programs
Activating parameter P4 resets all time programs (Pro1,
Pro2, Pro3) to the factory setting.
P5: Reset relative heating time
Activating parameter P5 resets the counter for relative
heating time (I2).
6. Cleaning, care and
maintenance
The appliance contains no user serviceable parts.
Material losses
◦ Never spray cleaning spray into the air slot.
◦ Ensure that no moisture can enter the appli-
ance.
◦ If a pale brownish discolouration appears on the ap-
pliance casing, wipe it off with a damp cloth.
◦ Clean the appliance when cold with ordinary clean-
ing products. Avoid abrasive or corrosive cleaning
products.
Options
±3 °C |
±5 °F
12 h | 24 h
°C | °F
on | off
on | off