Final Inspection - Beko HII63205MT Instructions D'installation

If your supply cord type is 5-conductor type,
for 1-phase connection:
For single phase connection
- (BRW/BLA) Brown/Black = L (Phase)
- (BLU/GRE) Blue/Grey = N (Neutral)
- (GR/YE) Green/yellow wire = (E)
(Earthing)
If your supply cord type is 5-conductor type,
for 2-phase connection:
- (BRW) Brown = L1 (Phase)
- (BLA) Black = L2 (Phase)
- (BLU/GRE) Blue/Grey = N (Neutral)
- (GR/YE) Green/yellow wire = (E)
(Earthing)
If your supply cord type is 4-conductor type,
for 2-phase connection:
- (BRW) Brown = L1 (Phase)
- (BLA) Black = L2 (Phase)
- (BLU) Blue = N (Neutral)
- (GR/YE) Green/yellow wire = (E)
(Earthing)
For the protection of the appliance
against burning:
• Make sure that the product plug is
securely plugged into the outlet to avoid
arcing.
• Do not use damaged cables or
extension cables.
• Ensure liquid or moisture is not
accessible to the electrical connection
point.
Placement and securing of the
appliance (Figures 5-6-7-8)
•
After preparing the installation location
of the appliance, turn the cooker upside
down and place it on a flat surface.
• Affix the sealing gasket supplied with
the appliance around the cooker so
that it shall be 1-2 mm inside the outer
edge of the glass as shown in Figure 5.
Ensure that no clearance is left between
both ends and between the glass and
gasket.
• Screw and secure the installation
springs supplied with the appliance
by engaging them to their seat on
the lower housing of the cooker as
shown in Figure 6. (In some models,
these springs may be secured to the
appliance ex-factory.)
• Turn the cooker again and align it with
the worktop and then place it on the
worktop. Cooker shall be placed on the
8
worktop thanks to the springs, and it
shall be easily secured.
• Ensure that the cooker and the
worktop are parallel when you place
the cooker on the worktop. When it is
not in parallel, connect the additional
installation clamps supplied with the
appliance as shown in Figure 8. Figure
8 shows the possible installation
locations of the clamps. (The locations
where the clamps can be attached
may vary depending on the product
model. You can connect according to
the mounting holes on your product.)
Ensure the parallelism by attaching the
clamps to the appropriate locations.
The type and quantity of clamps
supplied with the product may vary
depending on the product model.

Final inspection

• After completing the installation, turn on
the mains supply.
• Read the operation manual for the first
operation of the appliance.
• Ensure that each cooking hob heats.
Removal of the appliance
• Disconnect the mains supply of the
appliance.
• If your appliance is secured with
additional clamps, remove the screws
of the clamps first.
•
Remove the cooker by pushing upward
from the bottom of the cooker.
DE- Sicherheitshinweise
• Das Gerät muss von einer qualifizierten
Person in Übereinstimmung mit den
geltenden Vorschriften installiert
werden, damit die Garantie gültig bleibt.
Der Hersteller ist nicht verantwortlich
für Schäden, die durch von nicht
autorisierten Personen durchgeführte
Verfahren entstehen, die auch zum
Erlöschen der Garantie führen können.
• Es liegt in der Verantwortung des
Kunden, den Ort, an dem das Gerät
aufgestellt werden soll, vorzubereiten
und die Elektroinstallation vorbereiten
zu lassen.
• Das Gerät muss in Übereinstimmung
mit allen örtlichen Gas- und/oder
Elektrovorschriften installiert werden.
•
Entfernen Sie sämtliches