Functional Description - Makita TM3010C Manuel D'instructions

15. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
16. This tool has not been waterproofed, so do not
use water on the workpiece surface.
17. Ventilate your work area adequately when you
perform sanding operations.
18. Use of this tool to sand some products, e.g.
leaded paint surfaces, wood and metals could
expose user and bystanders to dust containing
hazardous substances.
respiratory protection.
19. Be sure that there are no cracks or breakage on
the pad before use. Cracks or breakage may
cause a personal injury.
20. Do not use accessories
specifically designed and recommended by the
tool manufacturer. Just because the accessory can
be attached to your power tool, it does not assure
safe operation.
21. Wear personal protective equipment. Depending
on application, use face shield, safety goggles
or safety glasses. As appropriate, wear hearing
protectors, gloves and workshop apron capable
of stopping small
fragments. The eye protection must be capable of
stopping flying debris
operations. The dust mask or respirator must be
capable of filtrating particles generated by your
operation. Prolonged exposure to high intensity
noise may cause hearing loss.
22. Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of
workpiece or of a broken accessory may fly away
and cause injury beyond immediate area of
operation.
23. Never lay the power tool down until the
accessory has come to a complete stop. The
spinning accessory may grab the surface and pull
the power tool out of your control.
24. Do not run the power tool while carrying it at
your side. Accidental contact with the accessory
could snag your clothing, pulling the accessory into
your body.
25. Do not operate the power tool near flammable
materials. Sparks could ignite these materials.
26. Do not use accessories that require liquid
coolants. Using water or other liquid coolants may
result in electrocution or shock.
27. Always be sure that the tool is switched off and
unplugged before carrying out any work on the
tool.
28. If working place is extremely hot and humid, or
badly polluted by conductive dust, use a short-
circuit breaker (30 mA) to assure operator safety.
29. Always be sure you have a firm footing. Be sure
no one is below when using the tool in high
locations.
30. Before starting operation, make sure that there
is no hidden supply lines such as electric, gas
and water lines under the working surface.
Cutting or damaging the supply lines may cause
electric shock, gas leakage, property damage, or
other accidents.
SAVE THESE INSTRUCTIONS.
6
Use appropriate
which are not
abrasive or workpiece
generated by various
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.

FUNCTIONAL DESCRIPTION

WARNING:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function
on the tool. Failure to switch off and unplug the tool
may result in serious personal injury from accidental
start-up.
Switch action (Fig. 1)
CAUTION:
• Before plugging in the tool, always check to see that
the tool is switched off.
To start the tool, slide the slide switch toward the "I (ON)"
position.
To stop the tool, slide the slide switch toward the "O
(OFF)" position.
Adjusting the orbital stroke rate (Fig. 2)
The orbital stroke rate is adjustable. To change the orbital
stroke rate, turn the dial between 1 and 5. The higher the
number is, the higher the orbital stroke rate is. Preset the
dial to the number suitable for your workpiece.
NOTE:
• The dial cannot be turned directly from 1 to 5 or from 5
to 1. Forcing the dial may damage the tool. When
changing the dial direction, always turn the dial moving
it through each intermediate number.
Constant speed control
Electronic speed control for obtaining constant speed.
Possible to get fine finish, because the orbital stroke rate
is kept constant even under load condition.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing or removing application tool (optional
accessory) (Fig. 3, 4, 5 & 6)
WARNING:
• Do not install application tool upside down. Installing
application tool upside down may damage the tool and
cause serious personal injury.
• Install attachment tool in the correct direction according
to your work. Application tool can be installed at an
angle of every 30 degree.
CAUTION:
• Be careful when closing the lock lever. The lock lever
may close suddenly and pinch your finger.
• Clean up dust and perform lubrication on the moving
part of the lock lever from time to time. Otherwise dust
may accumulate in the moving part of the lock lever
and hinder its smooth movement.
• Do not start the tool while the lever opens. The tool
may be damaged.
1. Open the lock lever fully. And remove the holder
bolt.