Oki IP-7900-26 Guide De Référence Rapide page 44

#ROLL END DETECTION Select whether to end the printing with an error or allow printing continuation after media end has been
>01:DETECT ONLY detected.
#ADVANCE PREF
Select the media advance adjustment value priority.
>XX:SOFTWARE
#PRINT MODE PREF
Select smart pass, density and print direction priorities.
>XX:SOFTWARE
#HEATER PREF
Select the heater temperature setting priority.
>XX:SOFTWARE
#PH REST PERIOD Scanning of the print head rests at every certain print length during printing. Set this time period to prevent
>XX:0000CYCLES missing dots when printing. Normally, set it to [0000CYCLES].
#PH REST TIME Corresponding to [ PH REST PERIOD], set the scan rest time. When [0] is set for [PH REST PERIOD], this parameter
>XX:10sec is ignored. Set this rest time to prevent missing dots when printing. Set it to [10 sec] as a rule of thumb.
#MEDIA ADV VALUE Set MEDIA ADVANCE VALUE. Set the advance value so that the banding (horizontal stripes of path splicing) is
>XX:YYY.YY% not visible.
#BACK ADJUST VAL Set the back adjust value of media. This value is used to correct the splice of two images divided by the auto-
>XX:+0000PULSE cleaning (PH CLEANING [MODE2] performed during printing.
#BIDIR ADJ1 L XXX
>XX:+00
The reciprocating correction adjusts the shift between two ways of bidirectional print. With this menu,
correction values for print modes (MAX SPEED and HIGH SPEED) are set.
#BIDIR ADJ1 R XXX
>XX:+00
#BIDIR ADJ2 L XXX
>XX:+00
The reciprocating correction adjusts the shift between two ways of bidirectional print. With this menu,
correction values for print modes (NORMAL) are set.
#BIDIR ADJ2 R XXX
>XX:+00
#BIDIR ADJ3 L XXX
>XX:+00
The reciprocating correction adjusts the shift between two ways of bidirectional print. With this menu,
correction values for print modes (HIGH QUALITY) are set.
#BIDIR ADJ3 R XXX
>XX:+00
#BIDIR ADJ4 L XXX
>XX:+00
The reciprocating correction adjusts the shift between two ways of bidirectional print. With this menu,
correction values for print modes (MAX QUALITY) are set.
#BIDIR ADJ4 R XXX
>XX:+00
#REMAINING MEDIA Set the remaining media. When the remaining media is set beforehand, you can check the remaining media (by
>XX:YYYm subtracting the printed length) in the MEDIA MENU.
#DELETE MEDIA
Delete the registered media. No. 01 to 20 of registered media can be selected.
>02:TYPE02 OK?
#COPY MEDIA Select the media number of copy source. Use this menu to copy the media information (parameters) of the
>XX registered media to other media. Designate the copy destination in [PASTE MEDIA].
#PASTE MEDIA
Select the media number of copy destination.
>01 à 02*
M.ADV MENU
Menu
#SING. ADV To determine the media advance value, print the media advance correction pattern with the current value.
#EXECUTE Then set the adjustment value.
#AUTO BIDIR ADJUST Print a bidirectional print position adjustment pattern and enter the correction value. Then all the correction
#EXECUTE value can be set automatically.
#MULTI ADV To determine the media advance value, print three media advance correction patterns centered on the current
#EXECUTE value. Then set the adjustment value.
#MANUAL BIDIR ADJUST
Print a bidirectional print position adjustment pattern for each print mode and set the correction value.
#EXECUTE
#BACK
Print the back correction pattern and set the back correction value.
#EXECUTE
REWIND MENU
Menu
REWINDING MEDIA
While you keep pressing the
PH.REC MENU
Menu
#PH RECOVERY
This menu is used to clean the print head of the printer. Press the
>NORMAL
head.
Outline of functions
Outline of functions
key, the printer rewinds media.
Outline of functions
key to enter PH.REC MENU for the print
43