Water Supply And Drain Connections - Hoshizaki KMD-201AA Notice D'utilisation

ENGLISH
7) Pass the Bin Control Connector through the hole from the bottom
to the top of the unit.
8) While pulling up the Bin Control Lead, hook the Bin Control on
the right side interior wall. Then push the Bin Control up against
the bottom of the unit, and slide to the back until it snaps in place.
Make sure the slotted holes at the right side of the Bin Control are
securely placed on the Collars at the bottom of the unit. See Fig. 4.
CAUTION
Make sure the Bin Control is securely in place. Otherwise, ice
may get between gaps and damage the Bin Control.
9) Connect the Bin Control Connector to the side of the Control Box.
0) Replace the Water Tank, Cube Guide, Pump Motor Bracket, Pump
Motor and Float Switch in their correct positions until they snap in
place.
) Secure the Pump Motor Bracket with the two Thumbscrews.
2) Reconnect the Pump Motor Connector and Float Switch
Connector.
3) Replace the Front Insulation and Front Panel in their correct
positions.
5. ELECTRICAL CONNECTIONS
WARNING
THIS APPLIANCE MUST BE EARTHED
This icemaker requires an earth that meets the national
and local electrical code requirements. To prevent possible
severe electrical shock to individuals or extensive damage to
equipment, install a proper earth wire to the icemaker. Remove
the plug from the mains socket before any maintenance, repairs
or cleaning is undertaken.
Pump Motor
Float Switch
Cube Guide
Fig. 3
Collars
Bin Control
Fig. 4
* This icemaker must have a separate power supply or receptacle of
220 - 240V.
* The main control box fuse is rated at 5A and should only be
replaced by a qualified service engineer.
* Usually an electrical permit and services of a licensed electrician
are required.
* If the supply cord and the plug should need to be replaced, it should
only be done by a qualified service engineer.
For the U.K. and the Republic of Ireland only
* The wires in the mains lead are coloured in accordance with the
following code:
Green & Yellow = Earth
Blue = Neutral
Brown = Live
As the colours of the wire in the mains lead of this appliance may
not correspond with the coloured markings identifying the terminals
in your plug, proceed as follows:
The wire which is coloured Green-and-Yellow must be connected
to the terminal in the plug which is marked with the letter E or by
the symbol or coloured Green or Green-and-Yellow. The wire
which is coloured Blue must be connected to the terminal which
is marked with the letter N or coloured Black. The wire which is
coloured Brown must be connected to the terminal which is marked
with the letter L or coloured Red.
* Should the socket outlets in the installation site not be suitable for
the plug supplied with your product, the plug must be removed (cut
off if it is moulded on plug) and an appropriate plug fitted.
If the non-rewirable plug has been cut from the power supply cord,
it must be disposed of. There should be no attempt to reuse it.
Inserting such a plug into a socket elsewhere presents a serious
risk of electrical shock.
* The non-rewirable plug must never be used without a fuse cover
being fitted.
The correct replacement for the detachable fuse cover is identifiable
from the manufacturer's reference number stamped on the plug.
Supply of replacement fuse covers can be obtained from Hoshizaki
Parts/Service Centres.
Fuses should be rated at 0A and approved to BS 362.

6. WATER SUPPLY AND DRAIN CONNECTIONS

(For the U.K. only, the connections must be in accordance with current
requirements of the Model Water Byelaws 986 SI No. 47)
* Only potable water should be used for this icemaker.
* To avoid performance reduction or malfunction caused by scaling,
the water supply should have a hardness of not more than 50
mg/L and a silica content of not more than 30 mg/L. Otherwise,
installation of a proper water treatment device will be required.
* Water supply pressure should be minimum 0.7 bar and maximum 8
bar. If the pressure exceeds 8 bar, use a pressure reducing valve.
Do NOT throttle back the supply tap.
* A plumbing permit and services of a licensed plumber may be
required in some areas.
* Water should drain into an open trap.
* The icemaker drain is gravity flow, so ensure drain pipe has an
adequate pitch or fall.
2