Technical Data; Approved Bar And Chain Combinations - Makita DCS 340 Manuel D'emploi Et De Sécurité

Technical data

Single-cylinder two-stroke
Piston displacement
Cylinder bore
Piston stroke
Max. power at speed
Max. torque at speed
Idling speed
Ignition system
Electronic, without breaker
Spark plug
or Spark plug
Electrode gap
Fuel system
Carburetor (for Canada)
Carburetor (for USA)
(all position diaphragm carburetor
with integral fuel pump)
Air filter
Fuel tank capacity
Fuel mixture
Weight
without cutting attachment
Cutting attachment
Guide bar
Cutting length
Safety saw chain (pitch) 3/8"
Drive link gauge .050"
Chain sprocket 6 teeth
Chain lubrication
Oil tank capacity

Approved bar and chain combinations

"Low-kickback saw chain is a chain which has met the
kickback performance requirements of ANSI B 175.1-
1991 (American National Standard for Power Tools-
Gasoline-Powered Chain Saws-Safety Requirements)
when tested on the representative sample of chain
saws below 3.8. C.l.D. specifed in ANSI B 175.1-
1991". The approved bar and chain combinations are
low kickback chains according to ANSI B 175.1-1991
and also meet the kickback requirements of CSA
Z62.3-96 for chain saws below 80 cm
The chain saw DCS 340, DCS 341, DCS 400, DCS
401 has been approved with following guide bar
and chain combinations:
Guide bar 3/8"
length Part no.
12" (30 cm) 442 030 661
14" (35 cm) 442 035 661
16" (40 cm) 442 040 661
"There may be other replacement bar and chain
combinations available that also reduces the risk of
injury from kickback".
DCS 340
2.0 cu. in (33 cm 3 ) 2.0 cu. in (33 cm
1.45" (37 mm) 1.45" (37 mm)
1.22" (31 mm) 1.22" (31 mm)
1.4/9,000 kW/rpm 1.4/9,000 kW/rpm 1.7/9,000 kW/rpm
1.7/6,500 Nm/rpm 1.7/6,500 Nm/rpm 2.0/6,500 Nm/rpm 2.0/6,500 Nm/rpm
2,600 rpm
NGK BPMR 6F NGK BPMR 6F
CHAMPION RDJ-7Y CHAMPION RDJ-7Y CHAMPION RDJ-7Y CHAMPION RDJ-7Y
.020" (0.5 mm) .020" (0.5 mm)
WALBRO WT 174 WALBRO WT 174
WALBRO WT 466 WALBRO WT 466
Robkoflok
13.3 oz. (0.4 l) 13.3 oz. (0.4 l)
see chapter "Fuel" see chapter "Fuel"
8 lbs. 9 oz. (3.9 kg) 8 lbs. 9 oz. (3.9 kg) 8 lbs. 13 oz. (4.0 kg) 8 lbs. 13 oz. (4.0 kg)
sprocket nose bar sprocket nose bar sprocket nose bar sprocket nose bar
12" (30 cm)
14" (35 cm)
16" (40 cm)
(528 092 ...)
X
(028 223 310) (028 223 310)
fully automatic oil fully automatic oil fully automatic oil
pump
7.1 oz. (0.21 l) 7.1 oz. (0.21 l)
3 .
Saw chain 3/8"
Part no.
528 092 646
528 092 652
528 092 656
DCS 341 DCS 400
3 ) 2.4 cu. in (39 cm
1.57" (40 mm)
1.22" (31 mm)
2,600 rpm 2,600 rpm
NGK BPMR 6F
.020" (0.5 mm)
WALBRO WT 174
WALBRO WT 466
Robkoflok Robkoflok
13.3 oz. (0.4 l)
see chapter "Fuel"
12" (30 cm) 12" (30 cm)
14" (35 cm) 14" (35 cm)
16" (40 cm) 16" (40 cm)
(528 092 ...) (528 092 ...)
X
(028 223 310)
pump pump
7.1 oz. (0.21 l)
WARNING
Do not use other replacement bars and chains
unless they have been designated as meeting the
ANSI B 175.1-1991 (for USA) and CSA Z62.3-96
(for Canada) kickback performance requirements
on that specific powerhead, or has been desig-
nated as "low kickback" saw chain in accordance
with the ANSI B 175.1-1991 (for USA) and CSA
Z62.3-96 (for Canada) standard.
DCS 401
3 ) 2.4 cu. in (39 cm
1.57" (40 mm)
1.22" (31 mm)
1.7/9,000 kW/rpm
2,600 rpm
NGK BPMR 6F
.020" (0.5 mm)
WALBRO WT 174
WALBRO WT 466
Robkoflok
13.3 oz. (0.4 l)
see chapter "Fuel"
12" (30 cm)
14" (35 cm)
16" (40 cm)
(528 092 ...)
X X
(028 223 310)
fully automatic oil
pump
7.1 oz. (0.21 l)
3 )
17