Quick BX 15 Manuel De L'utilisateur page 15

POS. DESCRIPTION
1A TANK 15L WITH HEAT EXCHANGER
1B TANK 20L WITH HEAT EXCHANGER
1C TANK 25L WITH HEAT EXCHANGER
1D TANK 30L WITH HEAT EXCHANGER
1E TANK 40L WITH HEAT EXCHANGER
1F TANK 50L WITH HEAT EXCHANGER
1G TANK 60L WITH HEAT EXCHANGER
1H TANK 80L WITH HEAT EXCHANGER
1I TANK 100L WITH HEAT EXCHANGER
2 RED PLASTIC WASHER
3 WHITE PLASTIC WASHER
4 BLUE PLASTIC WASHER
5 RELIEF/NON RETURN VALVE
6 HOSE CLAMP
7 DISCHARGE PIPE
8 A ELEMENT GASKET
FROM S/N 100.000
8 B ELEMENT GASKET
FROM S/N 200.000
9A ELECTRIC ELEMENT
1200W 220V
9B ELECTRIC ELEMENT
500W 220V
9C ELECTRIC ELEMENT
1200W 110V
9D ELECTRIC ELEMENT
600W 110V
10 BI-THERMOSTAT
11 POWER SUPPLY CABLE
12A BOILER RESISTOR COVER 220V
12B BOILER RESISTOR COVER 110V
13 NUT
14 GROUND CABLE TERMINAL
15 WASHER
16 SCREW 2,9 X 19
17A TANK MOUNTING
BX15-BX20-BX25
17B TANK MOUNTING
BX26-BX30-BX40
17C TANK MOUNTING
BX41-BX50-BX60-BX80
18 BOLT
19 WASHER
20 NUT
21 CABLE CLAMP
22 SCREW 2,9 X 16
BOILER BX15-100 - REV007A
CODE
M L B 1 5 2 6 0 S 0 0 0
M L B 2 0 2 6 0 S 0 0 0
M L B 2 5 2 6 0 S 0 0 0
M L B 3 0 3 2 0 S 0 0 0
• shut down power supply.
M L B 4 0 3 2 0 S 0 0 0
• Remove the protection cover (12) in order to reach
M L B 5 0 3 6 0 S 0 0 0
the thermostat (10).
M L B 6 0 3 6 0 S 0 0 0
• Push the reset button on the double thermostat (fig. 4).
M L B 8 0 3 6 0 S 0 0 0
• Replace on the protection cover (12).
M L B 1 0 0 3 6 0 S 0 0
• Switch on power supply.
P E C R B L R S 0 0 0 0
P E C R B L B N C 0 0 0
P E C R B L B L 0 0 0 0
M N VA L S 1 2 S 6 8 P
P B F 2 5 1 0 0 W 0 0 0
P V T B G M 1 0 N T 0 0
MAINTENANCE
P G G R E S 0 0 0 0 0 0
We recommend checking the magnesium anode (A) every
P G R M 4 3 5 0 0 0 0 0
12 months.
E V R 1 2 2 2 0 N 0 0 0 Replace the anode if its size has been reduced significantly.
This simple and preventive maintenance will ensure a long
E V R 0 5 2 2 0 N 0 0 0
life of the equipment.
E V R 1 2 1 1 0 N 0 0 0
F
E V R 0 6 1 1 0 N 0 0 0
E V T 1 5 S 0 0 0 0 0 0
E C C 3 0 1 5 0 G 0 0 0
P E C R B 2 2 0 0 0 0 0
P E C R B 1 1 0 0 0 0 0 The overpressure release device must be activated regular-
MBD04MXEN000
ly to remove calcium deposits and to ensure that it is not
E J C Y 0 4 0 0 0 0 0 0
blocked.
M B R 0 4 X 0 0 0 0 0 0
MBV02919AXCC
Periodically check the joints of the water pipe installation;
check the tightness of the securing screws and replace
M M S T B L 3 0 0 D R 1
them in case they are worn or corroded.
M M S T B L 4 0 0 D R 1
Also periodically check the electrical system working order.
M M S T B L 4 0 0 D R 1
MBV0830MXE00
M B R 0 8 X 0 0 0 0 0 0
MBD08MXEN000
P P B L B X 0 0 0 0 0 0
MBV02916AXCC
MAINTENANCE
WARNING: Quick nautic water heaters are provided
®
with a double thermostat with manual reset that
shuts down power supply in case of an excessive
water temperature.
If it happens, follow the instructions below:
if the high temperature safety system
WARNING:
switches on repeatedly, call Quick
During wintertime, when the water heater is not
in use it should be drained using the lever of the
valve (5). This is to avoid serious damage caused
by freezing.
EN
service center.
®
15