LENCO BT-9000 Mode D'emploi page 7

Antenna
For the best radio reception, fully extend the rod antenna located at rear of the unit.
MENU Option
In the FM radio mode, the unit allows you to select following options.
1. Press the MENU button entering menu mode.
2. Two options, [Scan setting] and [Audio setting] can be set by pressing the
TUNE +/- button from the remote control.
(a) Whilst [Scan setting] is displayed, press the ENTER button to conirm the selection.
- Then press main unit
[Strong stations].
Note:
[All stations]
[Strong stations] ----- FM scan stops only at stations with good signal strength.
- Press the ENTER button to conirm the desired selection when [All stations] or [Strong stations] displayed.
(b) Whilst [Audio setting] displays, press the ENTER button to conirm selection.
- Then press main unit
[Forced mono].
Note:
[Stereo]
[Forced mono]
- Press the ENTER button to conirm the desired selection when [Stereo] or [Forced mono] displayed.
3. You can press the MENU button to exit menu setting mode at any time.
Auto-scan and store Preset Stations
The unit allows you to store up to 20 FM stations for easy recall at any time.
1. Press the STANDBY
2. Press the FUNCTION button from the main unit or the DAB/FM button from the remote control to select FM radio
mode.
3. Press the SCAN button from the remote control until the frequency digits begin to change. The tuner will
automatically scan for stations from low to high frequency and then store them in the preset location.
Note: After each auto-scan & store operation, it will overwrite the existing preset stations by overwriting and
storing the new stations in their place.
4. To recall the preset station, press the CH +/- buttons from the remote control then press the ENTER button to
conirm selection.
FM Radio Tuning and manual store Preset Stations
1. Press the STANDBY
2. Press the FUNCTION button from the main unit or the DAB/FM button from the remote control to select FM radio
mode.
FM Radio Tuning
3. You can have following ways to tune to a desired station:
(a) Press the /
tuning step and tune to a desired radio station frequency igure.
(b) Press and hold the main unit
station frequency igure then release the button.
(c) For up-scan, press the main unit
button from the remote control and it will tune to the next higher radio station.
For down-scan, press the main unit
button from the remote control and it will tune to the next lower radio station.
Save preset station
4. Press the MEM button from the remote control. The preset channel number appears on display and blinks.
5. To select a desired preset station number, press the CH + / - buttons from the remote control.
Note: Each time the station number changed, it will display the current frequency or "Empty" of that preset
station location.
6. To conirm preset location, press the ENTER button and "Preset store" displays a while then returns to normal
tuner mode. The newly tuned frequency will replace the frequency in the selected preset station location.
7. Repeat steps 3 to 6 to store other stations, if apply.
Notes:
● There is a few seconds delay when programming, after this delay time, the unit will automatically switch back
to normal tuner mode.
● You can overwrite a preset station by overwriting and storing the new frequency in its place.
FM Radio Tuner Operation
/ buttons or remote control TUNE +/- buttons to display [All stations] or
----- By default FM scan stops at any available station (All stations). This may result in
poor quality audio from distant stations.
/ buttons or remote control TUNE +/- buttons to display [Stereo] or
----- By default, all stereo stations are reproduced in stereo. For weak stations, this may
result in poor quality audio. The audio quality can be improved using mono.
----- Reproduce mono audio only.
button to turn on the unit, where the power status indicator light on.
button to turn on the unit, where the power status indicator light on.
buttons from the main unit or the TUNE +/- buttons from the remote control with 0.05MHz
/ buttons or remote control TUNE +/- buttons and tune to a desired radio
button or remote control TUNE + button once then press the SCAN
button or remote control TUNE - button once then press the SCAN
GB 7
/ buttons from the main unit or the