Aiwa XR-MR5 Mode D'emploi page 27

Chaine stereo avec platines cd-r/cd
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

4 Set the timer-on time.
Turn MULTI JOG to the right to advance the time and to the left
to move the time back. The speed with which the time changes
varies according to how fast you turn MULTI JOG. You can
also use f or g. Holding these buttons down will vary the
time in 10-minute units.
Timer-on time
5 Press ENTER/ILLUMINATION.
Alternatively, press ENTER on the remote control.
6 Within 4 seconds, set the duration for the timer-
activated period.
Turn MULTI JOG, or press f or g to set the duration.
The duration can be set between 5 and 240 minutes in 5-minute
units.
Example: for timer recording from the radio
7 Within 4 seconds, press ENTER/ILLUMINATION.
Alternatively, press ENTER on the remote control.
8 Prepare the source.
For timer playback/recording of the radio, press TUNER to
select the band and tune in to the desired station.
For timer playback of a disc using the CD player of this unit,
load the disc in the CD player.
For timer playback of a disc using the CD-R/RW player/recorder
of this unit, load the disc in the CD-R/RW player/recorder.
For timer playback/recording of equipment connected to the
DIGITAL IN jack, press AUX/D-IN repeatedly so that "D-IN" is
displayed, and set the timer of the equipment so that play begins
at the same time.
For timer playback/recording of equipment connected to the
AUX/VIDEO IN jacks, press AUX/D-IN repeatedly so that "AUX"
is displayed, and set the timer of the equipment so that play
begins at the same time.
9 For timer recording, load a recordable CD-R or CD-
RW on the CD-R/RW player/recorder.
10 Adjust the volume and tone.
The source sound will be audible at the volume set here when
the power turns on at the set time.
• If the power economizing mode is activated, the volume for
timer recording will be 0 (minimum level). To monitor the sound
being recorded, deactivate the power economizing mode.
Timer-activated period
11 Press POWER to turn off the unit.
5, or 4 and 5 remain on the display after the power is
turned off (when the power economizing mode is deactivated).
When the timer-on time is reached, the unit turns on and begins
to play (or to record) with the selected source.
If the volume level was set to higher than 20 when the power
has turned off, it is automatically set to 20 when the unit turns
on by the timer.
NOTE
• Timer playback and timer recording will not begin unless the
power is turned off.
• If you use the unit while the timer is set, repeat steps 8 to 10 to
prepare the source and the recording destination, and adjust
the volume and tone before turning off the power.
• Timer recording from a CD or CD-R/RW to a CD-R/RW is not
possible.
To check the timer setting
Press TIMER while pressing SHIFT on the remote control. The
selected source, the timer-on time, and the duration for the timer-
activated period will be displayed for 4 seconds.
To change the timer setting
Set the timer again from the beginning.
To cancel the timer standby mode
Press JOG MODE repeatedly to call up the timer setting display,
then turn MULTI JOG so that "TIMER OFF" is displayed, and press
ENTER/ILLUMINATION.
When using the remote control, press TIMER repeatedly while
pressing SHIFT so that "TIMER OFF" is displayed.
To check the remaining time until the power is turned off during
timer play/recording
Press SLEEP while pressing SHIFT on the remote control.
The remaining time will be displayed for 4 seconds.
En
27
ENGLISH

Publicité

Table des Matières
loading

Table des Matières