GRAUPNER BRUSHLESS CONTROL 8 Instructions D'utilisation page 6

Setting the Standard Mode / First operation
ESC Stick Position setup
1. Make sure all the cable leads are properly connected.
2. Turn the transmitter on and check the servo travel of the throttle channel which should be ±100% or, with Multiplex R/C
systems, ±80%. Robbe/Futaba systems need reversing (REVERSE) the throttle arm travel! With Graupner/JR systems, the
latter should be set to "NORMAL". The throttle trigger should now be either at position "Brake" or at "Motor off"! The throttle
range is fixed. You may correct the transmitter way on the transmitter.
3. Turn the transmitter on (position "ON"), then push the throttle lever into position "Motor off / Brake".
4. Connect the battery to the controller, mind the correct polarity. Plug in the power battery and try only once to plug in. Do not
touch the contact several times.
5. If all wire connections are correctly connected, the motor should beep depending on the throttle stick position as like :
Do, Re ~~ Do, Re, Mi
Do, Re ~~
6. If you press and hold the Setup switch on the Switch box for over 1 second, the Green LED should flash.
At this time, if your hand is released from the Setup switch. The motor should beep like So, So, La, La, So, So and the Green
LED should flash one time.
7. Move the throttle sticker to the full position and press and release the switch, the Green LED should flash twice to indicate
that the full position has been set.
8. Move again the throttle stick to the neutral position ( if 3 position was set ) or minimum position ( if 2 position was set ) and
press and release the switch, the Green LED should flash triple time to indicate that the neutral position for 3 position or
minimum position for 2 position has been set,
9. At this stage, if you want to set 2 position, stay at the neutral position and press and release the switch /
If you want to set 3 position, move back the throttle stick to the minimum position and press and release the switch. After
finish the stick position setting above, the motor should beep like So, Fa, Mi, Re, Do sounds and the both LED should flash
alternately.
During the setting procedure, if you set wrong throttle stick, the Green LED should flash one time and the ESC is waiting for
resetting. Only after 3 position is set, the brake should be activated with Auto Brake Amount, Minimum Brake Amount,
Maximum Brake Amount
Note : It is ONLY necessary to make this initial throttle setup again if you are using a different transmitter or the settings have
been changed.
Programmable mode setting
1. Turn on the transmitter.
2. Connect the power battery, then the ESC should be automatically ON.
3. If all wire connections are correctly connected, the motor should beep depending on the throttle stick position as like :
Do, Re ~~ Do, Re, Mi
Do, Re ~~
4. If you press and hold the switch for over 1 second the Green LED should flash and if you continue to press and hold the
switch for over 4 seconds, the Red LED should flash. At this stage, if you release the switch, the ESC should beep Mi, Re, Do,
Re, Mi sound and the Red LED should flash once constantly to indicate that the ESC is now in the programmable mode setting.
Flashing repeatedly once enters the Battery type setting. 4 different program features can be set in this controllers as below.
Battery Type for all application
Motor rotation direction for all application
Governor Off or On for Heli / One or Two Way for Boat & Car
Select Air / Heli / Boat / Car
Setup Switch: The program function will change every time the Setup Switch is pressed.
. The Red LED will flash in accordance with the features as follows
1) Red LED flashes once ( Battery type setting available )
2) Red LED flashes twice ( Motor rotation direction setting available )
3) Red LED flashes three times (Governor Off/On, One/Two Way setting available )
4) Red LED flashes four times ( Model type Air or Heli or Boat or Car setting available )
If you press the Setup switch for over 2 seconds at a program function that you would like to change, the both LEDs should
flash.
ESC sound : Do, Re, Mi, Fa, So, La, Ti Do.
: When the throttle stick in the stop position.
: When the throttle stick is NOT in the stop position.
: When the throttle stick in the stop position.
: When the throttle stick is NOT in the stop position.