About Error Messages - Pioneer SGX-CA500 Mode D'emploi

Masquer les pouces Voir aussi pour SGX-CA500:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

About Error Messages

EN
Message
Charging impossible
Failed to start USB mass storage.
Disconnect, wait 5 minutes, reconnect
Storage space is getting low.
Please remove unnecessary data.
Please remove unnecessary data.
Battery level is low. Please connect
power supply.
Updating will start after fully charged.
Shutdown
Battery Level Decreasing
Catched data is inconsistent. Do you
want to try again?
Built-in flash memory error
File Error CODE:0001
60
Cause
You tried to charge the battery outside the
charging temperature range of 0 °C to 45 °C. You
cannot charge the battery outside the charging
temperature range of 0 °C to 45 °C for safety
reasons. The device may not have charged even
though the outside temperature is below 45 °C.
This happens because the device heats up when
the battery is charging.
The device stops charging when although it is not
charged enough even after a certain specified
charging time has passed.
This may happen because you charge the battery
while using Wi-Fi on the device with power on,
which causes to decrease the charging current.
USB connection failed. This message also appears
when the mass storage connection is not available
and the USB is connected such as during the
setting backup.
There is not enough free memory in the device
system area.
There is not enough free memory in the built-in
flash memory of the device. This message appears
when the update data is stored temporarily to the
built-in flash memory during the update procedure.
The device can be updated only when it is fully
charged to prevent update failures.
If the remaining battery is low, this message is
displayed before shutdown.
If the remaining battery is low, this message is
displayed 5 minutes before shutdown.
There is a failure in touch panel calibration data.
For example you didn't touch the plus mark during
the touch panel calibration.
There is a failure in file system of built-in flash
memory when you execute the initialization,
backup, or restore.
There is a file access error when you execute the
initialization, backup, or restore.
The system try to mount the file system when you
execute the initialization, backup, or restore. If the
system can't confirm the mount, this message is
displayed.
When the initialization, backup, or restore times
out, this message is displayed.
Solution
Charge the battery in the charging temperature
range of 0 °C to 45 °C. If you turn off the device
when the battery is charging, the temperature does
not rise (Ü page 6).
Turn off the device's Wi-Fi (Ü page 44).
Unplug the USB cable from the device, wait for a
while, and then try connecting again.
Transfer the ride log data to a PC. Delete the data
in the built-in flash memory from the PC (Ü page
26).
Transfer the ride log data to a PC. Delete the data
in the built-in flash memory from the PC (Ü page
26).
Charge the battery of the device. When charged
fully, the device starts updating automatically.
Not while charging : Charge the battery
While charging : Continue charging the battery
Not while charging : Charge the battery
While charging : Turn off the power and continue
charging the battery.
Tap the center of the plus mark during the touch
panel calibration.
Format the built-in flash memory.
If errors occur during the initialization, try to write
the firmware again. If you still cannot solve the
problem, contact your dealer.
If errors occur during the backup, transfer the
ride log data and backup data to a PC, and then
remove them from the built-in flash memory.
Remove the unnecessary files in the built-in
flash memory.
If errors occur during the restore, copy other
backup data from the PC to the device to restore
the data.
Format the built-in flash memory.
Retry to write the firmware.
If you cannot solve the problem, contact your
dealer.
Format the built-in flash memory.
Retry to write the firmware.
If you still cannot solve the problem, contact your
dealer.

Publicité

Table des Matières
loading

Table des Matières