1. Manuels
  2. Marques
  3. Varian Manuels
  4. Contrôleurs
  5. Turbo-V 250 PCB
  6. Notice de mode d'emploi

Varian Turbo-V 250 PCB Notice De Mode D'emploi

Masquer les pouces
Table des Matières

Publicité

Liens rapides

Télécharger ce manuel
Turbo-V 250 PCB
Controller
Model 969-9866
87-900-854-01 (C)
APRIL 2002
vacuum technologies
MANUALE ISTRUZIONI
BEDIENUNGSHANDBUCH
NOTICE DE MODE D'EMPLOI
MANUAL DE INSTRUCCIONES
MANUAL DE ISTRUÇÕES
BEDRIJFSHANDLEIDING
ISTRUKSTIONSBOG
BRUKSANVISNING
INSTRUKSJON MANUAL
OHJEKÄSIKIRJA
Ο∆ΗΓΙΕΣ ΧΡΗΣΕΩΣ
INSTRUCTION MANUAL

Publicité

Table des Matières
loading

Manuels Connexes pour Varian Turbo-V 250 PCB

Sommaire des Matières pour Varian Turbo-V 250 PCB

  • Page 1 Turbo-V 250 PCB MANUALE ISTRUZIONI Controller BEDIENUNGSHANDBUCH NOTICE DE MODE D’EMPLOI MANUAL DE INSTRUCCIONES Model 969-9866 MANUAL DE ISTRUÇÕES BEDRIJFSHANDLEIDING ISTRUKSTIONSBOG BRUKSANVISNING INSTRUKSJON MANUAL OHJEKÄSIKIRJA Ο∆ΗΓΙΕΣ ΧΡΗΣΕΩΣ INSTRUCTION MANUAL 87-900-854-01 (C) APRIL 2002...
  • Page 2 Turbo-V 250 PCB Controller...

  • Page 5: Table Des Matières

    BRUKERVEILEDNING ....................KÄYTTÖOHJEET ......................ODHGIES CRHSEWS......................41 INSTRUCTIONS FOR USE ..................… TECHNICAL INFORMATION ..................TURBO-V 250 PCB CONTROLLER DESCRIPTION ..............CONTROLLER SPECIFICATIONS ....................CONTROLLER OUTLINE ....................... INTERCONNECTIONS ........................Connection P1 - Logic Input Interconnections ............……….. Connection J2 - Logic Output Interconnections ..............…...
  • Page 6 Pump Shutdown ......................…….. Power Failure ........................Remote Control Mode Operation ..................RS 232 Control Mode Operation ................………….. ACCESSORIES AND SPARE PARTS ................... OPTIONS ............................

  • Page 7: Informazioni Generali

    PREPARAZIONE PER L’INSTALLAZIONE interventi non autorizzati o ad uso contrario alle normative nazionali specifiche. Il controller viene fornito in un imballo protettivo Il controller Turbo-V 250 PCB è un convertitore di speciale; se si presentano segni di danni, che frequenza, controllato...
  • Page 8 ISTRUZIONI PER L’USO Cavo di Interconnessione tra il Controller e la Pompa Interconnessioni tra il Controller ed il Transformatore INSTALLAZIONE NOTA Il controller installato nel sistema definitivo deve essere PERICOLO! posizionato in modo tale che l'aria di raffreddamento possa circolare liberamente intorno all'apparato. Non Le tensioni presenti tra il controller ed il relativo installare e/o utilizzare il controller in ambienti esposti trasformatore, e tra il trasformatore e la rete di...

  • Page 9: Procedure Di Uso

    è chiusa con la flangia di chiusura. MANUTENZIONE Di seguito è illustrato il pannello di comando dell'hand I controller della serie Turbo-V 250 PCB non richiedono held terminal. alcuna manutenzione. Qualsiasi intervento deve essere eseguito da personale autorizzato. In caso di guasto è...

  • Page 10: Messaggi Di Errore

    OVERVOLTAGE Si è verificato un guasto nella sezione di Premere due volte il pulsante START per alimentazione controller, riavviare la pompa. Se il messaggio si controller ha ricevuto un segnale spurio. ripresenta rivolgersi in Varian per la manutenzione. 87-900-854-01 (C)

  • Page 11: Gebrauchsanleitung

    Transportschäden müssen der zuständigen örtlichen automatischen Betrieb der Pumpenserie Turbo-V 250 Verkaufsstelle gemeldet werden. PCB erforderlichen Schaltungen. Der Controller steuert die Pumpen der Serie Turbo-V 250 PCB (durch einen 10-Schritte-Prozeß) in der Startphase, indem er die Spannung und die Stromstärke im Verhältnis zur Pumpen-geschwindigkeit kontrolliert.
  • Page 12 GEBRAUCHSANLEITUNG Verbundkabel zwischen Controller und Pumpe Verbundkabel zwischen Controller und Transformator INSTALLATION ANMERKUNG Der im definitiven System installierte Controller muß so GEFAHR! positioniert sein, daß die Kühlungsluft frei um das Gerät zirkulieren kann. Controller darf nicht Die Spannungen auf dem Controller und dem zugehörigen Umgebungen installiert u/o benutzt werden, die Transformator, sowie zwischen dem Transformator und Witterungseinflüssen (Regen, Frost, Schnee), Staub...

  • Page 13: Bedienung

    Schließflansch verschlossen ist. WARTUNG Nachstehend wird die Steuertafel des "Hand Held Terminals" beschrieben. Die Controller der Serie Turbo-V 250 PCB sind wartungsfrei. Eventuell erforderliche Eingriffe müssen von dazu befugtem Fachpersonal ausgeführt werden. Bei einem Defekt kann der Varian-Reparaturdienst bzw. der "Varian advanced exchange service" in Anspruch genommen werden, der für die Erneuerung...

  • Page 14: Fehlermeldungen

    Netzkabel wieder anschließen und die Pumpe durch zweimalige Betätigung der START-Taste neustarten. OVERVOLTAGE Defekt Versorgungsbereich Die Pumpe durch zweimalige Betätigung Controllers bzw. der Controller hat ein der START-Taste neustar-ten. Erscheint falsches Signal erhalten. die Meldung wieder sollte der Varian- Wartungs-dienst gerufen werden. 87-900-854-01 (C)

  • Page 15: Indications Generales

    Turbo-V 250 PCB. Le contrôleur pilote les pompes de la série Turbo-V 250 PCB (selon un processus subdivisé en dix pas) pendant la phase de mise en marche, en contrôlant la tension et le courant par rapport à...
  • Page 16 MODE D'EMPLOI Câble d’Interconnexion entre le contrôleur et la pompe Interconnexions entre le contrôleur et le transformateur INSTALLATION NOTE DANGER! Le contrôleur installé dans le système définitif doit être positionné de façon à ce que l'air de refroidissement Les tensions présentes entre le contrôleur et le puisse circuler librement autour de l'appareil.

  • Page 17: Procedures D'utilisation

    On présente ci-dessous le tableau de commande du ENTRETIEN “Hand Held Terminal”. Les contrôleurs de la série Turbo-V 250 PCB n'exigent aucun entretien. Toute opération doit être effectuée par un personnel agréé. En cas de panne, il est possible de s'adresser au Service de réparation Varian ou bien au "Varian advance exchange service"...

  • Page 18: Messages D'erreur

    Il s'est produit une panne de la section Presser deux fois l'interrupteur START d'alimentation du contrôleur, ou bien le pour remettre la pompe en marche. contrôleur a reçu un faux signal. Si le message se présente à nouveau, s'adresser à Varian pour l'entretien. 87-900-854-01 (C)

  • Page 19: Información General

    PREPARACIÓN PARA LA INSTALACIÓN autorizadas o al uso que no cumpla con las normas nacionales específicas. El controler se suministra en un embalaje de El controler Turbo-V 250 PCB es un convertidor de protección especial; si se observan señales de daños, frecuencia, controlado microprocesador, que podrían haberse producido durante el transporte,...
  • Page 20 INSTRUCCIONES DE USO Cable de interconexión entre el controler y la bomba Interconexiones entre el controler y el transformador INSTALLACIÓN NOTA El controler instalado en el sistema definitivo ha de ¡PELIGRO! colocarse de manera que el aire de refrigeración pueda circular libremente alrededor del aparato.

  • Page 21: Procedimientos De Uso

    MANTENIMIENTO A continuación se ilustra el panel de mando del hand Los controlers de la serie Turbo-V 250 PCB no held terminal. necesitan ningún mantenimiento. Cualquier operación ha de ser efectuada por personal autorizado. En caso de avería es posible utilizar el servicio de reparación...

  • Page 22: Mensajes De Error

    Apretar dos veces el pulsador START para OVERVOLTAGE sección de alimentación del controler o volver a poner en marcha la bomba. el controler ha recibido una señal Si el mensaje se vuelve a presentar espurio. dirigirse a Varian para el mantenimiento. 87-900-854-01 (C)

  • Page 23: Informações Gerais

    Turbo-V 250 PCB. O controller comanda as bombas da série Turbo-V 250 PCB (com um processo subdividido em dez passos) durante a fase de activação, controlando a tensão e a corrente em relação à...

  • Page 24: Instalação

    INSTRUÇÕES PARA O USO Cabo de interconexão entre o controller e a bomba Interconexões entre o controller e o transformador INSTALAÇÃO NOTA O controller instalado no sistema definitivo deve ser PERIGO! posicionado de modo que o ar de refrigeração possa circular livremente ao redor da aparelhagem.

  • Page 25: Procedimentos De Uso

    MANUTENÇÃO O controller da série Turbo-V 250 PCB não requer A seguir, está ilustrado o painel de comando do “Hand qualquer manutenção. Todas as operações devem ser Held Terminal”.

  • Page 26: Mensagens De Erro

    OVERVOLTAGE Verificou-se um defeito na secção de Premer duas vezes o botão START para alimentação do controller, ou o controller reactivar a bomba. Se a mensagem se recebeu um sinal falso. reapresentar, dirigir-se à Varian para a manutenção. 87-900-854-01 (C)

  • Page 27: Algemene Informatie

    Turbo-V 250 PCB. De controller stuurt de pompen van de serie Turbo-V 250 PCB (met een proces bestaande uit tien stappen) tijdens de startfase, en controleert hierbij de spanning en de stroom in verhouding tot de door de pomp bereikte snelheid.

  • Page 28: Installatie

    GEBRUIKSAANWIJZINGEN Verbindingskabel tussen controller en pomp Verbindingskabel tussen controller en transformator INSTALLATIE OPMERKING GEVAAR! De controller die definitief in het systeem geïnstalleerd wordt moet zodanig geplaatst worden dat de koellucht De spanningen aanwezig tussen de controller en de vrij rondom het apparaat kan circuleren. De controller bijbehorende transformator, en tussen de transformator mag niet geïnstalleerd en/of gebruikt worden in ruimten en het aanvoernet zijn dusdanig dat ze gevaar...
  • Page 29 Hier volgt de beschrijving van het bedieningspaneel ONDERHOUD van de hand-terminal. De controllers van de serie Turbo-V 250 PCB zijn onderho- udsvrij. Eventuele werkzaamheden moeten door bevoegd personeel worden uitgevoerd. In geval van storing is het mogelijk om de reparatiedienst van Varian of de "Varian advanced exchange service"...
  • Page 30 Er is een storing opgetreden in de Bedien twee maal de START-knop om de voedingssectie van de controller of de pomp weer op te starten. Als de melding controller heeft stoorsignaal weer verschijnt zich voor onderhoud tot ontvangen. Varian wenden. 87-900-854-01 (C)

  • Page 31: Generel Information

    Varian, før udstyret • temperatur: fra -20 °C til +70 °C anvendes. Varian tager ikke ansvar for skader helt eller • relativ luftfugtighed: 0 - 95% (ikke kondenserende) delvis følge tilsidesættelse disse instruktioner,...
  • Page 32 BRUGSANVISNING Forbindelseskabel mellem styreenhed og pump Forbindelseskabel mellem styreenhed og transformator INSTALLATION BEMÆRK ADVARSEL! Styreenheden skal anbringes på en sådan måde, at luft kan cirkulerer frit omkring apparatet. Installér og Spænding mellem styreenheden og transformatoren anvend ikke styreenheden i miljøer, der udsættes for samt mellem transformatoren og elnettet kan nå...

  • Page 33: Vedligeholdelse

    VEDLIGEHOLDELSE Følgende beskriver manøvrepanelet til hand-held terminalen. Styreenhederne i Turbo-V 250 PCB serien behøver ikke nogen vedligeholdelse. Ethvert indgreb på pumpen skal foretages af autoriseret personale. Hvis pumpen går i stykker, kan man benytte sig af Varians reparations-service eller Varian udvekslingsservice, hvor man kan få...
  • Page 34 OVERVOLTAGE Der er opstået fejl i styreenhedens Tryk to gange på START-knappen for at fødespænding eller styreenheden har starte pumpen igen. fået et falsk signal. Hvis meddelelsen kommer igen tag kontakt med Varian for nødvendig vedligeholdelse. 87-900-854-01 (C)

  • Page 35: Allmän Information

    åsidosättande instruktionerna, olämplig användning av person utan tillräcklig kunskap, obehörigt bruk av utrustningen eller FÖRBEREDELSER FÖR INSTALLATION hantering som strider mot gällande lokala föreskrifter. Styrenheten i Turbo-V 250 PCB serien är en mikro- Styrenheten levereras särskilt skyddande processorstyrd frekvensomvandlare som består av emballage.
  • Page 36 BRUKSANVISNING Anslutningskabel mellan styrenhet och pump Anslutningskabel mellan styrenhet och transformator INSTALLATION OBSERVERA VARNING! Styrenheten ska installeras permanent på ett sådant ställe, att kylluften kan cirkulera fritt kring apparaten. Spänningen mellan styrenhet och transformator samt Installera och använd inte styrenheten i miljöer som mellan transformator och elnätet kan nå...

  • Page 37: Instruktioner För Bruk

    Nedan beskrivs manöverpanelen för Hand Held underhållsfria. Allt servicearbete måste utföras av Terminalen. auktoriserad personal. Om styrenheten havererar, kontakta Varian reparation- sverkstad eller Varian utbytesservice, som kan ersätta styrenheten med en renoverad styrenhet. VARNING! Innan något arbete utförs på styrenheten måste dess strömförsörjning brytas.
  • Page 38 OVERVOLTAGE Ett fel i styrenhetens matningsdel har Tryck två gånger på knappen START för uppstått eller styrenheten har fått en att starta om pumpen. falsk signal. Om meddelandet visas igen, ta kontakt med Varian för nödvändigt underhåll. 87-900-854-01 (C)

  • Page 39: Generell Informasjon

    Dette utstyret er beregnet til bruk av profesjonelle Når styreenhetene transporteres eller lagres, må brukere. Brukeren bør lese denne brukerveiledningen følgende forhold være oppfylt: og all annen informasjon fra Varian før utstyret tas i • temperatur: fra 20 °C til +70 °C bruk.
  • Page 40 BRUKERVEILEDNING Forbindelseskabel mellom styreenhet og pump Forbindelseskabel mellom styreenhet og transformator INSTALLASJON MERK Styreenheten skal installeres på slik måte, kjøleluften kan sirkulere fritt rundt apparatet. Ikke ADVARSEL! installer eller bruk styreenheten i miljøer som utsettes Spenningen mellom styreenheten og transformatoren for regn, snø...

  • Page 41: Instruksjoner For Bruk

    BRUKERVEILEDNING BRUK INSTRUKSJONER FOR BRUK Dette avsnittet beskriver de viktigste driftsmomentene. For en detaljert beskrivelse samt moment som omfatter Starte styreenheten tilkoplinger eller ekstrautstyr vises det til avsnittet "Use" Styreenheten startes ved å sette strømkabelen i i vedlegget "Technical Information". Visse anvisninger veggkontakten.
  • Page 42 Trykk to ganger på knappen START for å OVERVOLTAGE Det har oppstått en feil i styreenhetens starte pumpen igjen. Vises feilmeldingen matedel, eller så har styreenheten fått et om igjen, må du ta kontakt med Varian for falskt signal. nødvendig vedlikehold. 87-900-854-01 (C)

  • Page 43: Yleisiä Tietoja

    Valvoja toimitetaan erityisessä suojaavassa vastaisesta käytöstä. pakkauksessa. Mikäli havaitsette mahdollisesti Sarjan Turbo-V 250 PCB valvoja on mikroprosessorin kuljetuksen aikana sattuneita vaurioita, ottakaa yhteys valvoma kiinteistä materiaaleista tehtyjä paikalliseen myyntitoimistoon. taajuudenmuuntimia, jotka kykenevät itsemäärittelyyn ja itsesuojaukseen. Valvoja ajaa Turbo-V 250 PCB sarjan pumppuja (kymmenportaisessa järjestelmässä)
  • Page 44 KÄYTTÖOHJEET Valvojan ja muuntajan litoskaapeli Valvojan ja muuntajan litäntä ASENNUS HUOM Valvojan sisällä syntyy korkeajännitettä, joka voi VAARA! aiheuttaa vakavia vammoja tai jopa kuoleman. Ennen minkätahansa valvojan huolto-tai asennustoimenpiteen Valvojan ja muuntajan välille ja myös muuntajan ja suorittamista, irroittakaa valvoja sähköverkosta.
  • Page 45 HUOLTO Turbo-V 250 PCB sarjan valvojat eivät kaipaa Seuraavassa on esitelty käsin pidettävän päätteen minkäänlaista huoltoa. Mahdolliset valvojaan tehtävät valvontapaneeli. toimenpiteet tulee jättää aina valtuutetun henkilön tehtäviksi. Toimintahäiriön sattuessa on mahdollista käyttää Varianin korjauspalvelua tai "Varian advance exchange service"...

  • Page 46: Vianetsintä

    START kaksi kertaa jolloin pumppu käynnistyy. OVERVOLTAGE Valvojan sähkövirran syötössä Painakaa painonappia START kaksi ilmennyt ongelma tai valvojan saama kertaa, jolloin pumppu käynnistyy. Mikäli signaali on väärä. viesti näkyy uudelleen kääntykää Varian huoltopalvelun puoleen. 87-900-854-01 (C)

  • Page 47: Odhgies Crhsews

    Ç eiv n ai exoplismev n oÇ miv a euruv c wrh Oi ruqmistev Ç thÇ seirav Ç Turbo-V 250 PCB eiv n ai ev n aÇ prostateutikhv suskeuasiv a . upav r coun endeiv x eiÇ blav b hÇ pou qa mporouv s an na ev c oun proklhqeiv katav th metatropev a Ç...
  • Page 48 ODHGIES CRHSEWS Sundev s eiÇ metaxuv tou ruqmisthv kai thÇ antliv a Ç Sundev s eiÇ metaxuv tou ruqmisthv kai tou Metaschmatisthv EGKATASTASH SHMEIWSH KINDUNOS O ruqmisthv Ç pou ev c ei egkatastaqeiv sto telikov suv s thma qa prev p ei na topoqethqeiv me tev t oio trov p o wv s te o aev r aÇ yuv x hÇ...
  • Page 49 STOP. Sth sunev c eia parousiav z etai o piv n akaÇ elev g cou tou SUNTHRHSH Hand Held Terminal. Turbo-V 250 PCB ruqmistev Ç thÇ seirav Ç apaitouv n kamiv a sunthv r hsh. Opoiadhv p ote epev m bash qa...
  • Page 50 . dev c qhke ev n a lanqasmev n o shv m a. xanaparousiasteiv mhv n uma apeuqunqeiv t e sthn Varian gia sunthv r hsh. 87-900-854-01 (C)

  • Page 51: General Information

    Turbo-V 250 PCB pump office. series. The controller drives (within ten steps) the Turbo-V 250 PCB pump during the starting phase by controlling the voltage and current respect to the speed reached by the pump. Remote start/stop, pump status signals, forepump start/stop, interlock control (for pressure switch, water flow switch, etc.) capability, are provided via auxiliary...
  • Page 52 INSTRUCTIONS FOR USE Interconnection Cable Controller - Pump Interconnection Cable Controller - Power Transformer INSTALLATION NOTE The controller installed into the customer system must WARNING! be positioned so that cold air can flow through the PCB components. Voltages between controller and power transformer and Do not install or use the controller in an environment transformer and mains are dangerous in case of exposed to atmospheric agents (rain, snow, ice), dust,...

  • Page 53: Use Procedure

    MAINTENANCE The following figure shows the hand held terminal control panel. The Turbo-V 250 PCB series controller does not require any maintenance. Any work performed on the controller must be carried out by authorized personnel. When a fault has occurred it is possible to use the Varian repair service.

  • Page 54: Error Messages

    OVERVOLTAGE Controller power supply circuitry is Press the START push-button twice to start faulty, or the Controller received a spike. the pump. Should the message still be present, call the Varian service. 87-900-854-01 (C)

  • Page 55: Technical Information

    TECHNICAL INFORMATION TURBO-V 250 PCB CONTROLLER DESCRIPTION Moreover, manages signals from sensors, input/output connection information to be displayed, The controller (model 969-9866) is a solid-state and gives outputs for a fully automatic operation. frequency converter which is driven by a single chip...

  • Page 56: Controller Specifications

    Frequency 933 Hz, ±2% CONTROLLER OUTLINE Power 150 W maximum The outline dimensions for the Turbo-V 250 PCB Operating temperature 0 °C to +40 °C controllers are shown in the following figures. Storage temperature -20 °C to +70 °C P1 optically insulated...

  • Page 57: Interconnections

    TECHNICAL INFORMATION INTERCONNECTIONS The following figure shows the Controller interconnections. Controller interconnections 87-900-854-01 (C)

  • Page 58: Connection P1 - Logic Input Interconnections

    NOTE must shorted allow Turbo-V 250 PCB pump to start if no interlock contact is connected. If, after starting the pump, the interlock contact opens, it has no effect on the operation and the pump continues to turn. The following figure shows a typical contact logic input connection and the related simplified circuit of the controller.

  • Page 59: Connection J2 - Logic Output Interconnections

    TECHNICAL INFORMATION Connection J2 - Logic Output Interconnections DESCRIPTION 7-14 R2 signal 24 V, 60 mA, optically isolated output (pin 14 positive, pin 7 negative). The output Voltage will be present upon the programmed condition delay YES or delay NO (see the cycle diagram in the following pages).

  • Page 60: Connection P6 - Low Power Fan

    This dedicated output optional Turbo-V 250 PCB pump cooling fan. The mating connector and cable are provided assembled with the air cooling kit. Controller to pump cable 87-900-854-01 (C)

  • Page 61: Controller-To-Power Connection

    TECHNICAL INFORMATION Controller-to-Power Connection The power supply from the external transformer must Primary 240 Vac 50/60 Hz be connected to J10 and J8 connectors. with 220/120/100 Vac The technical characteristics of the power transformer intermediate taps are detailed in the following table. secondary 19 Vac 0.3 A...

  • Page 62: Rs 232 Option

    TECHNICAL INFORMATION RS 232 OPTION Communication protocol: Host = Master RS 232 Installation Controller = Slave To install it, proceed as follows: The communication is performed in the following way: • Switch off the power and disconnect the power cord. •...
  • Page 63 Pump cycles number (integer coded in 2 bytes) Answer = after a request from the host, the Speed threshold Turbo-V 250 PCB controller will answer in one of the following ways: Run up time in seconds • (long coded in 4 bytes) •...
  • Page 64 (0 = NO I=YES) Soft Start Mode On request a sample program in QBasic language is (0 = NO I=YES) available by Varian. When the Request is "I" (Status readings), the Answer will contain a string of 2 characters with the following parameters:...

  • Page 65: Use

    S T A R T B U T T O N NOTE • Press the CURRENT push-button and the display When the Turbo-V 250 PCB pump is baked by a shows: membrane pump, the Soft Start mode should be deselected. 0 0 A K R P M X X °...

  • Page 66: Front / Remote Selection

    TECHNICAL INFORMATION • FRONT / REMOTE Selection Press the CYCLE NUMBER twice and the display shows: • Press CYCLE NUMBER and PUMP CURRENT pushbuttons together for at least 2 seconds and the processor enters in a routine where it is possible to X X X X C Y C L E X X X X X m program the controller.
  • Page 67 TECHNICAL INFORMATION • • Enter the selection by pressing PUMP Press the PUMP CURRENT pushbutton to enter the CURRENT pushbutton, and the display shows: value and the display shows: F R O N T R E M O T E 2 3 2 R S 2 3 2 S E L E C T...
  • Page 68 TECHNICAL INFORMATION • With connected, bidirectional Enter the value by pressing the PUMP CURRENT communication is established by selecting HOST. Data pushbutton, and the display shows: are sent to an external computer every time the external computer asks for the values. R S 2 3 2 H O S T P R I...

  • Page 69: Monitor Relay Programming

    TECHNICAL INFORMATION Monitor Relay Programming • Press the CYCLE NUMBER pushbutton to select the first number. • The display shows: S P E E D T H R E S H O L D S P E E D T H R E S H O L D S E L E C T I O N : X X K R P M S E L E C T...
  • Page 70 TECHNICAL INFORMATION • • Enter the value by pressing the PUMP CURRENT Enter the value by pressing the PUMP CURRENT pushbutton. push-button, and the display shows: R U N - U P I M E S E L X X h X X m X X s •...
  • Page 71 TECHNICAL INFORMATION • • Press the PUMP CURRENT push-button to enter Press PUMP CURRENT to confirm, and the display the data. shows: P U M P X X X X X h R E S E T ? X X X where: •...

  • Page 72: Starting The Pump

    TECHNICAL INFORMATION Starting the Pump • If the Soft Start mode has been deselected the display will change and shows: If the forepump and vent device are not operated by the controller, close the vent valve and switch on the forepump.

  • Page 73: Operating The Pump

    TECHNICAL INFORMATION Operating the Pump or twice if the display shows other parameters, either before starting the pump or after it is operating. After the starting period, if the system has a vacuum If LOW SPEED is selected before starting the pump, leak or the pressure in the pump/chamber is high (from the display shows: 1 mbar to atmosphere), the pump continues to operate...

  • Page 74: Pump Shutdown

    TECHNICAL INFORMATION With normal LOW SPEED operation, the pump will run Remote Control Mode Operation at about 2/3 of its nominal speed and achieves a base If remote signals are used to operate the controller, it pressure somewhat higher than standard must be programmed for remote operation (see specifications.

  • Page 75: Accessories And Spare Parts

    TECHNICAL INFORMATION ACCESSORIES AND SPARE PARTS DESCRIPTION PART NUMBER J1 input mating connector 969-9853 Power transformer 969-9867 RS 232 interface link kit 969-9851 OPTIONS DESCRIPTION PART NUMBER P2 output mating connector 969-9852 Hand held terminal 969-9860 87-900-854-01 (C)

  • Page 76: Customer Information

    NOTE: If a product is received at Varian which is contaminated with a toxic or hazardous material that was not disclosed, the customer will be held responsible for all costs incurred to ensure the safe handling of the product, and is liable for any harm or injury to Varian employees as well as to any third party occurring as a result of exposure to toxic or hazardous materials present in the product.
  • Page 77 Request for Return FAILURE REPORT TURBO PUMPS and TURBOCONTROLLERS POSITION PARAMETERS Power: Rotational Speed: Does not start Noise Vertical Current: Inlet Pressure: Does not spin freely Vibrations Horizontal Temp 1: Foreline Pressure: Does not reach full speed Leak Upside-down Mechanical Contact Overtemperature Other: Temp 2:...
  • Page 78 Tel: (39) 011 997 9111 Tel: (39) 011 997 9111 Fax: (39) 011 997 9350 Brazil Fax: (39) 011 997 9350 Varian Industria e Comercio Ltda. Japan Avenida Dr. Cardoso de Mello 1644 Internet Users: Varian Vacuum Technologies Vila Olimpia Customer Service &...

Ce manuel est également adapté pour:

969-9866

Table des Matières