Technical Data; Inserting/Replacing The Battery - Bosch GMS 100 M Professional Notice Originale

10 | English
Intended Use
The measuring tool is intended for detecting ferrous and non-
ferrous objects and "live" conductors.
Product Features
The numbering of the product features shown refers to the
illustration of the measuring tool on the graphic page.
1 Illuminated ring
2 Marking hole
3 Display
4 On/Off button
5 Contact pads
6 Sensor area
7 Type plate
8 Battery lid
9 Latch of battery lid
10 Fixture for carrying strap
11 Carrying strap
12 Protective pouch*
* The accessories illustrated or described are not included as
standard delivery.
Display Elements (see figure A)
a Switched-off audio signal indicator
b Warning-function indicator
c Indication of the object type "Non-magnetic metal"
d Indication of the object type "Magnetic metal"
e Indication of the object type "Live conductor"
f Temperature control indicator
g Battery indicator
h Main scale
i Fine scale

Technical Data

Digital Detector
Article number
Maximum scanning depth*
– Ferrous metals
– Non-ferrous metals (copper)
– Live conductors 110–230 V
(voltage applied)**
Automatic switch-off after approx.
Operating temperature
Storage temperature
Relative air humidity, max.
*depending on operating mode, material and size of the objects, as well
as material and condition of the base material
**less scanning depth for wires/conductors that are not "live"
In terms of accuracy, the measuring result can be inferior in case
of unfavourable surface quality of the base material.
Please observe the article number on the type plate of your measuring
tool. The trade names of the individual measuring tools may vary.
1 609 929 Y44 | (28.4.11)
Digital Detector
Battery
Operating life time, approx.
Degree of protection (excluding
battery compartment)
Weight according to
EPTA-Procedure 01/2003
Dimensions
(length x width x height)
*depending on operating mode, material and size of the objects, as well
as material and condition of the base material
**less scanning depth for wires/conductors that are not "live"
Please observe the article number on the type plate of your measuring
tool. The trade names of the individual measuring tools may vary.
Declaration of Conformity
We declare under our sole responsibility that the product
described under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents:
EN 61010-1:2010-10, EN 61326-1:2006-05,
EN 301489-3:2002-08, EN 301489-1:2008-04,
EN 300330-1:2010-02, EN 300330-2:2010-02 according
to the provisions of the directives 2004/108/EC,
1999/5/EC.
Dr. Egbert Schneider
Senior Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
GMS 100 M
Leinfelden, 23.03.2011
Professional
Assembly
3 601 K81 100

Inserting/Replacing the Battery

100 mm
80 mm
Alkali-manganese batteries are recommended for the meas-
uring tool.
50 mm
To open the battery lid 8, press the latch 9 in the direction of
5 min
the arrow and fold up the battery lid. Insert the supplied bat-
tery. Pay attention that the polarity is correct, according to
–10 °C...+45 °C
the representation on the inside of the battery lid.
–20 °C...+70 °C
The battery indicator g always indicates the current battery
80 %
status:
–
–
–
–
In terms of accuracy, the measuring result can be inferior in case
of unfavourable surface quality of the base material.
Battery fully charged
Battery has 2/3 of its capacity or less
Battery has 1/3 of its capacity or less
Please change battery
If the measuring tool is not used for a long period of
time, the battery must be removed. The battery can cor-
rode or discharge itself over long periods.
GMS 100 M
Professional
1 x 9 V 6LR61
IP 54 (dust and splash
water protected)
260 g
200 x 86 x 32 mm
Dr. Eckerhard Strötgen
Head of Product
Certification
Bosch Power Tools
5 h