Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
2.8
SELF-RETRACTING DEVICES WITH LEADING EDGE (SRD-LE): The SRDs covered by this instruction manual include
Self-Retracting Devices with Leading Edge capabilities (SRD-LEs). See Figure 1 for specific SRD-LE models. SRD-LEs were
tested for horizontal use and falls over a steel edge without burrs. SRD-LEs may be used in situations where a fall may
occur over steel edges, such as found on steel shapes or metal sheeting.
Leading Edge Precautions: Observe the following precautions when using SRD-LEs:
•
The allowable angle of redirection of the lifeline portion of the SRD-LE at the edge over which a fall might occur
(measured between the two sides formed by the redirected lifeline) shall be at least 90 degrees (see Figure 7).
•
The anchor point shall be situated at the same height as the edge at which a fall might occur or above the edge.
Anchor points below the edge are dangerous because they cause the lifeline to redirect at an angle sharper than 90
degrees (see Figure 7).
•
Consult Section 1 for limitations to the allowable work area relative to the anchorage point, including factors such
as swing fall and abrasion on the line at the edge and the use of a single anchor point versus anchors that allow
horizontal movement (e.g., Horizontal Lifeline or Horizontal Rail).
•
SRD-LEs may be used with a Horizontal Lifeline or Horizontal Rail only as instructed in the product instructions for the
Horizontal Lifeline or Horizontal Rail.
•
Do not work on the far side of an opening opposite the SRD-LE anchorage point.
•
In the event of a fall over the edge, special rescue measures may be required.
•
When planning your Leading Edge application, be sure work area parameters are within the Minimum Setback
Distance, Maximum Free Fall Distance, and Minimum Fall Clearance Required when Falling Over an Edge as indicated
on the SRD-LE labeling.
Leading Edge Fall Clearance Calculation: The Minimum Fall Clearance Required when Falling Over an Edge can be
calculated based on the Setback Distance and Distance Along the Edge of your Leading Edge application (see Figure 8). To
calculate Fall Clearance from the table in Figure 8:
1.
Select the value closest to your Setback Distance (A) in the left-side row headings.
2.
Select the value closest to your working Distance Along the Edge (B) from the top column headings. Shaded areas
with no values indicate the Distance Along the Edge is outside of the safe Work Radius for your selected Setback
Distance.
3.
The Clearance Required when Falling Over an Edge (C) will be the value listed at the intersection of the row selected
in Step 1 and the column selected in Step 2.
4.
Repeat the previous steps for every edge over which the worker could potentially fall to determine safe placement of
anchorage and allowable Work Radius.
CE Sharp Edge Definitions: These CE Self-Retracting Devices have been successfully tested for horizontal use and for
falls over a steel edge without burrs. Setback distance restrictions shown in Figure 8 must be observed. Avoid working
where the lifeline will continuously or repeatedly abrade against sharp or abrasive edges. Eliminate such contact or
protect edges using a heavy pad or other means. Edge Types are defined as follows:
•
VG 11.60 revision 6 Type A Edge Definition: A steel edge with a radius fo r=0,5 mm and without burrs was used
for the test. Per testing, the equipment may be used over similar edges, as can be found on rolled steel profiles,
wooden beams, or clad, rounded parapets.
•
VG 11.54 revision 6 Type B Edge Definition: A steel edge made of sharp-edged drawn square steel bar in
accordance with EN 10278:1999-12 without radii (material C 45+C or E 335 GC [ST60] pursuant to EN 10025). Per
testing, the equipment may be used over similar edges, as can be found on trapezoidal sheet metal.
12
Publicité
Table des Matières
