Factory Settings; Exit Programming Mode - Farfisa Alba Série Mode D'emploi

PROGRAMMING
EN
"Extended Range" DUO Systems Block Ad-
dress and Device Address (PDX1)
The Audio CA2124AB and Audio-Video CV-
2124AB Modules are compatible with Extended
Range DUO Farfisa digital systems as they
support the possibility to divide the system into
99 blocks with 253 devices for each, therefore
more than 25,000 devices can be installed in
the system. To obtain such performance, each
device must be identified by a Block Address
(section of the system to which the device
belongs: 001 to 099) and a Device Address
(address programmed in the device: 001 to
253); Block 000 (i.e. unprogrammed block) is
reserved for compatibility with existing DUO
products and diagrams.
External Video Modulators (PDX1)
The Audio CA2124AB and Audio-Video
CV2124AB Modules are designed to drive
external video modulators (VM2521 type or
similar) to which up to 8 additional cameras
can be connected.
Each additional camera is managed as an
External Unit and must have its own address
within the range of addresses reserved
to external units (from 231 to 253); these
addresses must be stored in the VM1 to
VM8 parameters of the audio-video module
(codes 151 to 158).
Following the request of the video inter-
com system, the image of the camera on
the module (by default=Main Camera) will
be displayed first and then, cyclically, the
additional cameras from VM1 to VM8 (if
fewer cameras are saved, the display cycle
will automatically take into account only the
cameras saved); once the cycle has finished,
it will start again with the display of camera
on the module and so on.
To change the camera with which the display
sequence starts, you will need to store in
the TP parameter (code159) the address of
the new main camera chosen from those
stored in the VM1 to VM8 parameters. To
reconfigure the camera on the module as
the main camera, it is necessary to store the
address 255 in the TP parameter.

Factory settings

The following are the values of the default factory
settings, if you need to change them follow the
instructions in the following paragraphs.
- Single button operation mode
- Main Camera (TP)=255 (camera on the mod-
ule)
- Audio-Video module address=231
- Address associated with Button 1= 99
- Address associated with the First Button of
the first additional pushbutton module (single
button configuration)=101
- Electric Lock activation time=1 Second
- Special function buttons=none
Entering programming mode
Entering programming is only done with the
unit in standby mode. To enter programming,
you need to:
simultaneously hold pressed keys 2 and 4
for 4 seconds;
after the 4 sec. the module emits a tone and
the symbol starts flashing quickly;
within 5 seconds press buttons 1, 2, 3 and 4
sequentially, the symbol flashes quickly
and the module emits a tone every 4 sec. to
indicate that you are in programming mode.

Exit programming mode

To exit programming, you need to:
simultaneously keep pressed keys 2 and 4
for 4 sec.;
After 4 sec. the module emits a tone and the
symbol turns off.
Entering codes and values
To enter codes and values, use the keys 1/
and 2; their use is as follows:
1/ : This button is pressed to confirm the
entering of a code or to switch to
another programming phase.
2: This button is pressed to increase the
value of the digit to be entered. Press
the button a number of times equal to
the digit to be entered (digit 1=1 press,
digit 9=9 presses, digit 0=10 presses of
the button).
Button pressing is confirmed by a tone.
Notes on entering codes and values
- The codes and values to be entered must
be always formed by three digits (hundreds,
tens, and units); codes and values that are
composed of tens and units or units alone must
be completed by adding zeros. For example,
number 96 becomes 096 and number 5
becomes 005.
- The digits must be entered one by one by
pressing "n" times the "2" button, where"
n "corresponds to the value of the digit to
be entered, followed by a pause of about 2
seconds to switch to the next digit (a tone will
indicate when switching to entering the next
digit). For example, to enter number 096 you
need to:
- press the "2" button 10 times to enter the
digit 0 and wait for 2 seconds until you
hear a tone;
- press the "2" button 9 times to enter digit 9
and wait for 2 seconds until you hear a tone;
- press the "2" button 6 times to enter the
digit 6 and wait for 2 seconds until you
hear a tone.
Attention: after composing the number,
always remember to confirm the entry by
pressing the key 1/ .
Configuring call buttons of the Door
Station
With the following programming it is possible to
select the configuration of the buttons of the Door
Station (default setting is single-button mode).
Single-button or double-button
The audio-video module and the additional
button modules connected to it (up to 8) can
work as:
Single-Button Double-Button
P1 P1 P1 P3
P2 P2 P2 P4
P3 P3 P3 P9
P4 P4 P4 P10
P5 P5 P5 P11
P6 P6 P6 P12
To make the selection you need to:
Enter programming.
For single-button operation, simultane-
ously press for 4 sec. keys 1 and 2, the
module emits a tone and the 2 symbols
and are lit simultaneously for 2 sec.
For double-button operation, simultane-
ously press for 4 sec. keys 1 and 3, the
module emits a tone and the 2 symbols
and are lit simultaneously for 2 sec.
Exit programming.
Attention: the programming is active both
on the audio-video module and on all the
additional button modules connected to it.
In the case of selecting single-button
operation, by default, the buttons will call
the following addresses:
P1
099
P2
100
P3
101
P4
102
P5
103
P6
104
P1 P1
P2 P2
P P5
P P6
P P7
P8 P
P1
099
P2
100
P3
101
P4
102
P5
103
P6
104
- 22 -
Mi 2530