How To Use Your Microwave Oven Safely; Important - Sammic HM-1900 Mode D'emploi

3. Keep the oven away from heat and water.
Exposure to heat and water can lower oven efficiency and lead to malfunctioning,
so be sure to install the oven away from external heat and water sources.
4. This oven conforms to EMC Directive 89/336/EEC, however some interferen-
ce may occur if it is placed too close to a radio or TV, so keep them as far apart
as possible.
5. Exhaust vents are located at the rear of the oven so maintain a minimum spa-
cing of 5cm (2") between the oven and any adjacent surfaces at theses points.
In an enclosed housing, please maintain a minimum spacing of 20cm on the top.
Covering the exhaust vent may lead to malfunctioning. Hot air flows from these
vents, so be sure not to obstruct cover or let curtains come between the oven
and the rear wall.
6. When you stack your microwave ovens.
1) Place one microwave oven on top of the other one, and remove the plates
which are each secured by a single screw to the bottom-left corners at the rear
of both microwaves. (Fig. 1)
2) Remove the two screws which are securing the frame of the lower microwa-
ve oven. Remove the screw which is securing the bottom-right corner of the
upper microwave oven. (Fig. 2)
3) Use the upper and lower plate screw holes to secure the upper and lower
microwave ovens with the four screws. Secure the bottom-left corner of the
lower microwave also. (Fig. 2-a)
4) Drive a plastic spacer in the duct hole of the upper unit.
WARNING-THIS APPLIANCE MUST BE EARTHED

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow: Earth.
Blue: Neutral.
Brown: Live.
As the colours of the wires in the mains lead of this appliance may not corres-
pond with the coloured marking identifying the terminals in your plug, proceed
as follows:
The wire which is coloured green-and-yellow must be connected to the termi-
nal in the plug which is marked with the letter E or by the earth symbol or colou-
10 ENGLISH
red green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is
marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is
marked with the letter L or coloured red.
THIS PLUG IS NOT WATERPROOF - KEEP DRY
This cord is already fitted with a moulded plug incorporating a fuse, the value
of which is indicated on the pin face of the plug. Should the fuse need to be
replaced, an ASTA approved BS1362 fuse must be used of the same rating,
marked thus.
If the fuse cover is detachable, never use the plug with the cover omitted. If a
replacement fuse cover is required, ensure it is the same colour as that visible
on the pin face of the plug. Fuse covers are available from Sanyo Service
Centre.
If the plug supplied is not suitable for your socket outlet, it should be cut off and
destroyed*.
The end of the flexible cord should be suitably prepared and the correct plug fit-
ted.
*WARNING: A PLUG WITH BARED FLEXIBLE CORDS IS HAZARDOUS IF
ENGAGED IN A LIVE SOCKET OUTLET.

HOW TO USE YOUR MICROWAVE OVEN SAFELY

Although your oven is provided with safety features, it is important to observe
the following:
a) It is important not to defeat or tamper with safety interlocks.
b) Do not place any object between the oven front face and the door or allow
residue to accumulate on sealing surfaces. Wipe the sealing area frequently
with a mild detergent, rinse and wipe dry.
Never use abrasive powders or pads.
c) When opened, the door must not be subjected to strain, for example, a child
hanging on an opened door or any load could cause the oven to fall forward to
cause injury and also damage to the door.
Do not operate the oven if it is damaged, until it has been repaired by a quali-
fied service engineer. It is particularly important that the oven door closes pro-
perly and that there is no damage to the :
i) Door (bent)
ii) Hinges and Latches (broken or loosened)
iii) Door seals and Sealing surfaces
d) It is dangerous for anyone other than a properly qualified service engineer
to carry out adjustments or repairs.