Antenna Installation; Manual Programming - BFT ALPHA Instructions D'installation

8 INTEGRATED RECEIVER TECHNICAL SPECIFICATION
Receiver output channels:
- output channel 1, if activated, controls a START command
- output channel 2, if activated, controls the excitation of the 2nd radio
channel relay for 1s.
Transmitter versions which can be used:
all Rolling Code transmitters compatible with

ANTENNA INSTALLATION

Use an antenna tuned to 433MHz.
For Antenna-Receiver connection, use RG8 coaxial cable.
The presence of metallic masses next to the antenna can interfere with
radio reception. In case of insu cient transmitter range, move the an-
tenna to a more suitable position.
9) PROGRAMMING
Transmitter storage can be carried out in manual mode, or by means of
the Universal palmtop programmer which allows you to create installa-
tions in the "collective receivers" mode, as well as manage the complete
installation database using the EEdbase software.

10) MANUAL PROGRAMMING

In the case of standard installations where no advanced functions are
required, it is possible to proceed to manual storage of the transmitters
1) If you wish the transmitter T key to be memorised as Start, press thSW1
button on the control unit, otherwise if you wish the transmitter key to be
memorise as second radio channel, press the SW2 button on the control
unit.
2) When the DL1 LED blinks, press the transmitter P1 hidden key, and
the DL1 LED will stay on permanently.
3) Press the key to be memorised on the transmitter, LED DL1 will start
blinking again.
4) To memorise another transmitter, repeat steps 2) and 3).
5) To exit the storage mode, wait until the LED is switched o completely.
IMPORTANT NOTE: ATTACH THE ADHESIVE KEY LABEL TO THE FIRST
MEMORISED TRANSMITTER (MASTER).
In the case of manual programming, the rst transmitter assigns the
key code to the receiver; this code is necessary in order to carry out
subsequent cloning of the radio transmitters.
10.1) CONTROL UNIT MEMORY CANCELLATION
In order to cancel the control unit memory completely, simultaneously
press for 10 seconds the SW1 and SW2 buttons on the control unit (DL1
LED blinking). Correct memory cancellation will be indicated by the DL1
LED staying on permanently. To exit the storage mode, wait until the
LED is switched o completely.
11) RECEIVER CONFIGURATION
The on-board receiver combines characteristics of utmost safety in copy-
ing variable code (rolling code) coding with the convenience of carrying
out transmitter "cloning" operations thanks to an exclusive system.
Cloning a transmitter means creating a transmitter which can be au-
tomatically included within the list of the transmitters memorised in
the receiver, either as an addition or as a replacement of a particular
transmitter.
Cloning by replacement is used to create a new transmitter which takes
the place of the one previously memorised in the receiver; in this way
a speci c transmitter can be removed from the memory and will no
longer be usable.
Therefore it will be possible to remotely program a large number of ad-
ditional transmitters or, for example, replacement transmitters for those
which have been lost, without making changes directly to the receiver.
When coding safety is not a decisive factor, the on-board receiver allows
you to carry out xed-code additional cloning which, although abandon-
ing the variable code, provides a high number of coding combinations,
therefore keeping it possible to "copy" any transmitter which has already
been programmed .
12) RADIO-TRANSMITTER CLONING (Fig.7)
Rolling-code cloning / Fixed-code cloning
10 - ALPHA-ALPHA BOM
INSTALLATION MANUAL
Make reference to the universal palmtop programmer instructions and
the CLONIX Programming Guide.
12.1) ADVANCED PROGRAMMING: COLLECTIVE RECEIVERS
Make reference to the universal palmtop programmer Instructions and
the CLONIX Programming Guide.
.
13) ACCESSORIES
SPL ( g.4).
Pre-heating optional board. Recommended for temperatures below
-10°C. (In the case of hydraulic motors).
ME ( g.5).
Optional board used to connect a 12V~ electric lock.
Note: the ME optional board is not operated by the START control of the
integrated radio board. For the correct functioning of the ME optional
board use one of the following con gurations:
1. use the second radio channel as START control and perform the neces-
sary connections to the terminal board.
2. use the plug-in radio receiver.
EBP ( g.2).
The EBP electric lock with continuous service can be connected directly
to terminals 1 and 4.