Important - Kenwood FDM30 Instructions

to use your food processor
1 Fit the detachable drive shaft onto the power unit
2 Then fit the bowl by aligning the
on the power unit, turn clockwise
3 Fit an attachment over the bowl drive shaft.
Always fit the bowl and attachment onto the processor
l
before adding ingredients.
4 Fit the lid - ensuring the top of the drive shaft/tool locates
3
into the centre of the lid.
Do not use the lid to operate the processor,
l
always use the on/off speed control.
5 Plug in, switch on and select a speed. (Refer to the
recommended speed chart).
The processor will not operate if the bowl or lid
l
are not fitted correctly into the interlock. Check
that the feed tube and bowl handle are situated
to the right front hand corner.
Use the pulse (P) for short bursts. The pulse will operate for
l
as long as the control is held in position.
6 Reverse the above procedure to remove the lid, attachments
and bowl.
Always switch off and unplug before removing
l
the lid.

important

Your processor is not suitable for crushing or grinding coffee
l
beans, or converting granulated sugar to caster sugar.
When adding almond essence or flavouring to mixtures
l
avoid contact with the plastic as this may result in
permanent marking.
Plastic blender
A
to use your blender
1 Fit the sealing ring into the blade assembly

the seal is located correctly in the grooved area.
Leaking will occur if the seal is damaged or
l
incorrectly fitted.
2 Hold the underside of the blade assembly
blades into the goblet - turn anti-clockwise until it is secure
. Refer to the graphics on the underside of the blade
4
assembly as follows:
- unlocked position
- locked position
The blender will not operate if incorrectly
assembled.
3 Put your ingredients into the goblet.
4 Fit the lid onto the goblet and turn clockwise
clicks. Fit the filler cap.
5 Place the blender onto the power unit, align the
blender with the on the power unit and turn clockwise
to lock .
The appliance will not operate if the blender is
l
incorrectly fitted to the interlock.
6 Select a speed (refer to the recommended speed chart) or
use the pulse control.
.
1
on the bowl with the
until it locks .
2
(if supplied)
- ensuring

and insert the

until it
5
on the
Glass blender
B
to use your blender
1 Fit the sealing ring
seal is located correctly in the grooved area.
Leaking will occur if the seal is damaged or
l
incorrectly fitted.
2 Screw the goblet onto the blade assembly
graphics on the underside of the blade unit as follows:
- unlocked position
- locked position
The blender will not operate if incorrectly
assembled.
3 Put your ingredients into the goblet.
4 Fit the lid to the goblet and push down to secure
filler cap.
5 Place the blender onto the power unit, align the
blender with the
to lock .
The appliance will not operate if the blender is
l
incorrectly fitted to the interlock.
6 Select a speed (refer to the recommended speed chart) or
use the pulse control.
multi mill
(if supplied)
Use the multi mill for processing nuts, coffee beans and
purées.
1 Put the ingredients into the jar
2 Fit the sealing ring
3 Turn the blade assembly upside down. Lower it into the jar,
blades down.
4 Screw the blade assembly onto the jar until finger tight
. Refer to the graphics on the underside of the blade
7
assembly as follows:
- unlocked position
- locked position
5 Place the multi mill onto the power unit, align the
the mini multi mill with the
clockwise to lock
8
6 Switch onto maximum speed or use the pulse control.
grinding mill
Use the grinding mill for processing dry ingredients such as
coffee beans and for grinding spices such as:-
Black peppercorns, cardamom seeds, cumin seeds,
coriander seeds, fennel seeds, fresh ginger root, garlic
cloves and fresh chillies.
6
to use your grinding mill.
1 Place your ingredients into the blade assembly
2 Fit the lid and turn clockwise to lock
cq
3 Place the mill onto the power unit and turn clockwise to lock
.
bk
4 Select a speed or use the pulse (P).
5
(if supplied)
into the blade unit - ensuring the
 
4
on the power unit and turn clockwise
.
c
into the blade assembly
co
on the power unit and turn
.
(if supplied)
.
9
. Refer to the
. Fit the
5
on the
6
.
cp
on
.
cr