Polisher Safety Warnings - Makita PV7000C Manuel D'instructions

ENGLISH
(Original instructions)
1 Switch trigger
2 Lock button
3 Speed adjusting dial
4 High-low speed setting button
5 Cover
6 Side grip
SPECIFICATIONS
Model
Max. capacities
Sponge pad / Wool bonnet ................................. 180 mm
Spindle thread ........................................................... M14
Rated speed (n) /
No load speed (n ) ....................................... 2,100 min
0
Overall length ...................................................... 210 mm
Net weight .............................................................. 2.1 kg
........................................................
Safety class
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for polishing, smoothing before
painting, finishing surfaces, and removing rust and paint.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.

POLISHER SAFETY WARNINGS

Safety Warnings Common for Polishing Operation:
1. This power tool is intended to function as a
polisher. Read all safety warnings, instructions,
illustrations and specifications provided with
this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
2. Operations such as grinding, sanding, wire
brushing or cutting-off are not recommended to
be performed with this power tool. Operations for
which the power tool was not designed may create a
hazard and cause personal injury.
4
Explanation of general view
7 Backing pad
8 Spindle
9 Wrench
10 Sponge pad
11 Pad
12 Wool bonnet
3.
PV7000C
4.
–1
5.
/II
6.
ENE051-1
7.
ENF002-2
GEA010-1
8.
GEB038-3
9.
10. Position the cord clear of the spinning acces-
11. Never lay the power tool down until the acces-
13 Lock nut
14 Rubber pad
15 Lock nut wrench
16 Limit mark
17 Brush holder cap
18 Screwdriver
Do not use accessories which are not specifi-
cally designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories can-
not be adequately guarded or controlled.
Threaded mounting of accessories must match
the tool spindle thread.
mounted by flanges, the arbour hole of the
accessory must fit the locating diameter of the
flange. Accessories that do not match the mounting
hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
Do not use a damaged accessory. Before each
use inspect the accessory such as backing pad
for cracks, tear or excess wear. If power tool or
accessory is dropped, inspect for damage or
install an undamaged accessory. After inspect-
ing and installing an accessory, position your-
self and bystanders away from the plane of the
rotating accessory and run the power tool at
maximum no-load speed for one minute. Dam-
aged accessories will normally break apart during
this test time.
Wear personal protective equipment. Depending
on application, use face shield, safety goggles
or safety glasses. As appropriate, wear dust
mask, hearing protectors, gloves and workshop
apron capable of stopping small abrasive or
workpiece fragments. The eye protection must be
capable of stopping flying debris generated by vari-
ous operations. The dust mask or respirator must be
capable of filtrating particles generated by your oper-
ation. Prolonged exposure to high intensity noise
may cause hearing loss.
Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of work-
piece or of a broken accessory may fly away and
cause injury beyond immediate area of operation.
sory. If you lose control, the cord may be cut or
snagged and your hand or arm may be pulled into
the spinning accessory.
sory has come to a complete stop. The spinning
accessory may grab the surface and pull the power
tool out of your control.
For accessories