How To Put The Headphone Unit; How To Replace The Headphones; Maintenance - Panasonic RP-WFG20 Mode D'emploi

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 12
Operation
AUTO ON/OFF function
See illustrations
When the transmitter receives audio input, the power
is turned on ([OPR/CHG] indicator lights up in green).
When the transmitter has not received audio input for
approximately 3 minutes, the power is automatically
turned off ([OPR/CHG] indicator goes out).
When the volume of the connected unit is too low, this
function doesn't work. Turn up the volume as much as
possible without causing distortion.
Note
Even if the transmitter's power is automatically turned
off, some noise may be generated when the headphone
unit is still on. This is not a malfunction.
If reception is still poor
See illustrations
Interference may occur between the radio waves from
the transmitter and other radio waves. You can change
the transmitter channel to improve reception. If you use
the unit near a cordless telephone, it may cause radio
interference.
Before changing the transmitter channel:
Make sure that the headphone unit is turned off.
1. Select another channel with [CHANNEL] switch.
2. Press [POWER
frequency automatically.
Note
Some sound or noise may still be heard even if no
sound signals are passing through the transmitter.
ENHANCING SPEECH
See illustrations
ENHANCING SPEECH can be used to make human
voice easier to hear.
1. Make sure that the headphone unit is turned on
([OPR] indicator is red).
The function only works when the headphone unit is
turned on.
2. Press [ENHANCING SPEECH] button.
[OPR] indicator turns to green. The enhancing speech
function is enabled.
● To disable the function, press [ENHANCING
SPEECH] button again. [OPR] indicator turns to red.
● When the headphone unit is turned off and turned on,
the unit starts up with the last enabled/disabled status
of the function.
Note
When using bone conduction headphones, this function
may not be effective.
Resetting the unit
This unit can be reset if all operations are rejected. To
reset the unit, press the end of a thin object, such as a
paper clip, into the [RESET] switch on the upper part
of the receiver.
10
22
on page 4.
on page 4.
/TUNING] button to adjust the
on page 4.

How to put the headphone unit

See illustrations
on page 5.
1. Hold the headphone unit correctly, with [OPR]
indicator outward.
2. Slowly expand the arms, and put the right and left
speakers.
● Do not excessively pull the arms apart.
Put the bone conduction headphones
3. Hang the hook
on the tragus (triangle part)
This will give you the most appropriate position.
● If you put the headphones in the incorrect position,
you may not hear sounds well from the speakers
and the surrounding environment.
Put the In-Ear headphones
3. Insert the earpieces into ears.
● If earpieces do not fit your earholes properly, a
low pitch could not be heard due to the decreased
sealing property. In order to enjoy higher quality
sound, insert earpieces farther into the ears by
turning them slightly.
● If earpieces do not fit to your earholes, replace
them with other earpieces sets supplied.

How to replace the headphones

See illustrations
on page 5.
Remove the headphones
While pressing and holding the release buttons on
the both sides of the receiver, pull out the current
headphones from the receiver.
Mount the headphones
Mount the other headphones on the receiver.
● Insert the plug on the headphones to the jack on
the receiver, and connect them.

Maintenance

Wipe with a soft, dry cloth.
● When extremely dirty, wipe away the dirt using a cloth
dampened with water and firmly wrung out, and then
wipe away any remaining moisture with a dry cloth.
● Do not use solvents such as benzine, thinner, alcohol
and kitchen detergent, or chemically treated cloth.
Doing so may degrade the exterior case or cause the
paint to peel.
.

Publicité

Table des Matières
loading

Table des Matières