Connecting To Power; Power Supply - Roadstar HRA-1550USMP Manuel D'instructions

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

29. Audio signal L/R output port
30. Audio signal L/R input port
31. 3.5mm Earphone jack

CONNECTING TO POWER

Before switching on make sure that the voltage of your electricity supply is the same as that
indicated on the rating plate.
For your own safety read the following instructions carefully before attempting to connect this
unit to the mains.
MAINS (AC) OPERATION
This unit is designed to operate on AC 230V 50Hz current only. Connecting it to other power
sources may damage the unit.
CAUTION
To prevent electric shock disconnect from the mains before removing cover. No user serviceable
parts inside. Refer servicing to qualified service personnel.
SAFETY PRECAUTION
Do not allow this unit to be exposed to rain or moisture.
Mains Supply: 230V 50Hz - AC only
This symbol means that this unit is double insulated. An earth connection is not required.

POWER SUPPLY

Remove the stereo carefully from the box, retaining the packaging for future use.
AC POWER OPERATION
Connect the plug to a mains power inlet 230V AC ~ 50 Hz.
Note: If the Audio from CD, USB, SD or AUX-IN input is missing for 15 or more than 15
minutes, the unit can switch OFF itself. If you want to turn the unit on after it switches
off itself, please turn the VOLUME ON/OFF Knob to OFF position first, and then turn
the unit on.
FM TUNER
note: If none of function buttons is pressed, the default state will be FM after the unit
is turn on.
1) Switch the function knob to AM/FM-ST/SW1/SW2 position.
2) Turn the Tuning Knob (13) to tune to your favourite station.
English
3
3) In order to receive a better FM-ST/SW1/SW2 program, extend the rod antenna (27) as long
4. FM STEREO indicator (16), when it receives a clear and stable radio station of FM-ST, the
PLAYING COMPACT DISC
Note: If there is error during the playing of CD / USB / SD card occasionally, please turn
off the unit and restart it. Then it can return to normal playback.
Handle Compact Discs
To remove a CD from its storage case, press down on the centre of the case and lift the
 Hold the disc by the edges. Avoid touching the recorded side of the disc.
Loading CDs
Press the CD / USB button, then press OPEN / CLOSE button to open the CD door.
Place the CD in the compartment with the label side facing upwards.
 Close the CD door by hand. When fully closed, there will be "LOAD" appears on LED
Please note:
 Do not put anything other than a CD in the compartment. Other objects can damage the
 Do not force to open/close the CD door by hand at any time.
 Keep the CD door closed when not in use to prevent dirt and dust from getting into the
 Never insert more than one CD at a time.
 If a disc is deeply scratched or too dirty, it may not play.
Playing CD
 When the disc is put into the unit, the unit will read the disc and display the total number of
 If the disc is in CD format, the CD indicator will light.
 If the disc is in MP3 format, the MP3 indicator will light.
 If the disc is in WMA format, the WMA indicator will light. After displaying the total number
 Press STOP button to stop playing.
After pressing STOP button, you can press OPEN/CLOSE button to open CD door to get
English
4
as possible, and then rotate the antenna with 360 degrees, until it can receive the signal
clearly.
color of Power Indicator / FM Stereo Indicator will change to green blue from green, it is in
stereo state.
disc out.
(Do not force to open the CD door by hand at any time.)
display and CD will turn after about ten seconds. Then the LED Display will indicate the
total number of tracks on the disc.
mechanism.
mechanism.
the tracks.
of the tracks, the unit will play from the 1st song automatically.
out of the CD disc at any time.

Publicité

Table des Matières
loading

Table des Matières