Changing The Tool - Bosch PSB 700-2 RE Instructions D'emploi

OBJ_DOKU-1584-003.fm Page 5 Monday, January 23, 2006 10:30 AM
Loosen the wing bolt 19 and place the auxiliary handle
12 with the mounted extraction device onto the spindle
collar of the impact drill in such a manner that the
adapter 18 engages into the corresponding opening
below the keyless chuck. Tighten the wing bolt 19.
Cleaning the Extraction Device (see figure B)
Slide the locking latch 20 upward or empty the dust
collector 16 before placing down the extraction device.
The dust collector 16 is sufficient for approx. 40 drill-
ings with a drilling diameter of 6 mm.
When the extraction starts to get weaker or when the
dust collector 16 is about half full, the dust collector 16
must be emptied. For this, push the release buttons 15
and remove the dust collector 16.
Pull the filter element 21 from the dust collector 16
downward. Empty and clean the dust collector 16.
Clean the filter element 21 by striking or tapping out the
dust.
Check the filter element 21 for damage and replace it
as required.
Firstly, place the filter element 21 into the dust collector
16 and then insert the dust collector 16 into the bottom
of the extraction device, then swivel the dust collector
upward until it latches at the top.
Removing the Extraction Device
Loosen the wing bolt 19 and pull the auxiliary handle 12
with the mounted extraction device from the spindle
collar of the impact drill.
Tilt the adapter 18 to the stop and pull the telescopic
guide 14 out of the auxiliary handle 12.
Auxiliary Handle (models with dust
extraction)
Always use the power tool with the auxiliary han-
dle 12 provided.
The auxiliary handle 12 can be used with or without the
mounted extraction device. The auxiliary handle 12 can
be fastened in two different positions, see Chapter
"Mounting the Extraction Device".
Adjusting the Drilling Depth (see figure C)
With the extraction device mounted, the drilling depth
"X" can be adjusted.
Insert a drill bit into the drill chuck and clamp the drill bit
as described in Chapter "Changing the Tool". Rotate
the set collar for the depth stop 13 downward until it
can be moved alongside the telescopic guide 14. Place
the machine, without switching it on, firmly against the
edge of the surface to be drilled until the drill bit pro-
trudes out of the extraction device by the length of the
required drilling depth "X". Slide the set collar for the
depth stop 13 until it faces against the auxiliary handle
12 and rotate the set collar upward in order to lock the
determined distance.
2 609 001 190 • 23.1.06
Auxiliary Handle (models without dust
extraction) (see figure D)
Operate your machine only with the auxiliary
handle 23.
The auxiliary handle 23 can be set to any position for a
secure and low-fatigue working posture.
Turn the wing bolt for adjustment of the auxiliary
handle 19 in anticlockwise direction and set the auxil-
iary handle 23 to the required position. Then tighten the
wing bolt 19 again in clockwise direction.
Adjusting the Drilling Depth (see figure D)
The required drilling depth X can be set with the depth
stop 24.
Press the button for the depth stop adjustment 22 and
insert the depth stop into the auxiliary handle 23.
Pull out the depth stop until the distance between the
tip of the drill bit and the tip of the depth stop corre-
spond with the desired drilling depth X.

Changing the Tool

Before any work on the machine itself, pull the
mains plug.
Keyless Chuck (PSB 1000-2 RCA/PSB 800-2 RA)
(see figure E)
The drill spindle is locked when the On/Off switch 9 is
not pressed. This makes quick, convenient and easy
changing of the tool in the drill chuck possible.
Open the keyless chuck 1 by turning until the tool can
be inserted. Insert the tool.
Firmly tighten the collar of the keyless chuck 1 by hand
in clockwise direction until the locking action ("click") is
no longer heard. This automatically locks the drill
chuck.
The locking is released again to remove the tool when
the collar is turned in the opposite direction.
Keyless Chuck (PSB 700-2 RE) (see figure F)
Tightly hold the rear sleeve of keyless chuck 1 and turn
the front sleeve anticlockwise until the tool can be
inserted. Insert the tool.
Tightly hold the rear sleeve of the keyless chuck 1 and
firmly turn the front sleeve clockwise by hand until the
locking action is no longer heard. This automatically
locks the drill chuck.
The locking is released again to remove the tool when
the front sleeve is turned in the opposite direction.
Screwdriver Tools (see figures G–H)
When working with screwdriver bits 25, a universal bit
holder 26 should always be used. Use only screwdriver
bits that fit the screw head.
For driving screws, always position the "Drilling/Impact
Drilling" selector switch 2 to the "Drilling" symbol.
English–5