Intended Use - Black & Decker BCBL700 Mode D'emploi

English
2. Insert the battery pack into the charger.
3. The green LED will flash indicating that the battery is
being charged.
4. The completion of charge is indicated by the green LED
remaining on continuously. The pack is fully charged
and may be used at this time or left on the charger.
Leaving the battery in the charger
The charger and battery pack can be left connected with
the green LED glowing indefinitely. The charger will keep
the battery pack fresh and fully charged.
Important Charging Notes
1. Longest life and best performance can be obtained if
the battery pack is charged when the air temperature
is between 65 °F – 75 °F (18 ° – 24 °C). DO NOT charge
when the battery pack is below +40 °F (+4.5 °C), or
above +104 °F (+40 °C). This is important and will
prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 65 °F – 75 °F (18 ° – 24 °C);
d. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the battery pack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Charger Cleaning Instructions

WARNING:
the charger from the AC outlet before cleaning. Dirt
and grease may be removed from the exterior of the
charger using a cloth or soft non-metallic brush. Do
not use water or any cleaning solutions.
6
Shock hazard. Disconnect
SAVE THESE
INSTRUCTIONS
FOR FUTURE USE
THIS PRODUCT USES THE BATTERY
AND CHARGER LISTED IN THE CHART
BELOW.
DEsCRiPTiOn
20V Max* Lithium-Ion
Battery:
20V Max* Lithium-Ion
Battery Charger:
2 Amp Fast Charger:
COMPONENTS (FIG. A)

Intended Use

This cordless handheld blower is designed for household
blowing applications.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
ASSEMBLY AND ADJUSTMENTS

WARNING:
serious personal injury, turn unit off and remove
the battery pack before making any adjustments
or removing/installing attachments or
accessories. An accidental start-up can cause injury.

CAUTION:
before removing extension attachment or end
attachment. An attachment must be attached to the
housing before use.
Blow Tube Assembly (Fig. B, C)
• To attach the blower tube
the peg 5 on the bottom of the power head with the
notch 6 on the bottom of the blower tube opening as
shown in Fig. B.
• Push the blower tube onto the power head until the
tube locks 2 engage the blower tube and an audible
click is heard.
CATAlOg nUMBER
ʵ LBXR20
ʵ LB20
ʵ LBX20
ʵ LBXR20BT
ʵ LBXR2020
ʵ LCS20
ʵ LCS201
ʵ LCS1620
ʵ L2AFC
ʵ L2AFCBST
ʵ LCS200
To reduce the risk of
Ensure the battery is removed
to the power head, line up
3