UNITEC Climate WT3081 Manuel De L'utilisateur page 20

5. Press the „ENTER" button 2.
6. Use „" 3 and „" 4 to set the maximum
temperature for the alarm.
7. Activate the HI outdoor temperature alarm by
pressing the „  ON/OFF" button 5.
8. Press the „ENTER" button 2.
9. Use „" 3 and „" 4 to set the minimum tem-
perature for the alarm.
10. Activate the LO outdoor temperature alarm by
pressing the „  ON/OFF" button 5.
11. Press the „ENTER" button 2; the maximum
value and „max mem" begin to flash.
12. Press the „ENTER" button 2 for 3 seconds to
delete the maximum value.
13. Press the „ENTER" button 2.
14. Press the „ENTER" button 2; the minimum value
and „min mem" begin to flash.
15. Press the „ENTER" button 2 for 3 seconds to
delete the minimum value.
16. Press the „ENTER" button 2 to complete the
programming procedure.
Note: Every time the alarm is activated by pressing
the „  ON/OFF" button 5 the bell icon  appears
on the display.
INDEX, SETTING ALARM VALUES
UV index classification
Very high
High
Extreme
Normal
Low
1. Press the „MENU" button 1 ten times until the UV
index display flashes.
2. Use „▲" (3) and „▲" (4) to set the maximum index (0
– 12) for the alarm.
3. Activate the HI UV index alarm by pressing the „
ON/OFF „ button (5.
4. Press the „ENTER" button (2); the maximum value
and „max mem" begin to flash.
5. Press the „ENTER" button (2) for 3 seconds to
delete the maximum value.
6. Press the „ENTER" button (2) to complete the
programming procedure.
WIND, SETTING ALARM VALUES AND DISPLAY
1. Press the „MENU" button 1 eleven times until
the wind speed display flashes.
2. Use „" 3 and „" 4 to choose average wind
speed or gust speed „GUST".
3. Press the „ENTER" button 2.
4. Use „" 3 and „" 4 to choose the speed unit
(km/h, m/s, bft, mph, knots).
English
313531__Funk-Wetterstation_Manual_180223.indd 20
5. Press the „ENTER" button 2.
6. Use „" 3 and „" 4 to set the maximum
7. Activate the HI speed alarm by pressing the
8. Press the „ENTER" button 2.
9. Use „" 3 and „" 4 to choose the wind direc-
10. Activate the HI wind direction alarm by pressing
11. Press the „ENTER" button 2; the maximum
12. Press the „ENTER" button 2 for 3 seconds to
13. Press the „ENTER" button 2 to complete the
Note: Every time the alarm is activated by pressing
the „  ON/OFF" button 5 the bell icon  appears
on the display.
LIGHT INTENSITY, SETTING ALARM VALUES
AND DISPLAY
1. Press the „MENU" button 1 twelve times until the
= 10, 11, 12+
2. Use „" 3 and „" 4 to set the light unit (fc, lux,
= 7, 8, 9
= 5, 6
3. Use „" 3 and „" 4 to set the maximum bright-
= 3, 4
4. Activate the HI brightness alarm by pressing the
= 0, 1, 2
5. Press the „ENTER" button 2; the maximum value
6. Press the „ENTER" button 2 for 3 seconds to
7. Press the „ENTER" button 2 to complete the
Note: Every time the alarm is activated by pressing
the „  ON/OFF" button 5 the bell icon  appears
on the display.
RAIN MEASUREMENT, SETTING ALARM
VALUES AND DISPLAY
1. Press the „MENU" button 1 twelve times until the
2. Use „" 3 and „" 4 to choose the display
3. Press the „ENTER" button 2.
4. Use „" 3 and „" 4 to set the rainfall unit (mm,
5. Press the „ENTER" button 2.
6. Use „" 3 and „" 4 to set the maximum rain-
7. Activate the HI rainfall alarm by pressing the
20
speed for the alarm.
„  ON/OFF" button 5.
tion for the alarm.
the „  ON/OFF" button 5.
value and „max mem" begin to flash.
delete the maximum value.
programming procedure.
light brightness display flashes.
W/m²).
ness value for the alarm.
„  ON/OFF" button 5.
and „max mem" begin to flash.
delete the maximum value.
programming procedure.
rainfall display flashes.
period (1 h, 24, week, month, total).
inch).
fall for the alarm.
„  ON/OFF" button 5.
26.02.18 09:14