Technical Specifications - Felco 801-HP Manuel D'utilisation

• In the framework of shipping the complete FELCO 801
assembly (FELCO 801-HP 15
FELCO 880 POWERPACK, or only the battery(ies) 09:
follow the applicable standards. Battery 09 is a product
classified as per UN 3481, class 9 packaging group II.
SAFETY MEASURES RELATED TO THE USE OF
THE TOOL
• Verify that switch 07 is set to "OFF" position, before
disconnecting battery 09 from the control housing 04, or
disconnecting pruning shear 15 from the cord 02.
• Disconnect pruning shear 15 from its cord 02 before
any intervention thereon (replacement of blade 17,
etc...).
• Do not dismantle the pruning shear 15. Only the
operations contained in this manual are allowed.
• Do not store the pruning shear 15 in humid areas.
• Never carry the pruning shear 15 or the control
housing 04 by the cord 02.
• Do not try to cut wood of particularly big diameter, or
materials other than wood, unless otherwise indicated.
• Retain the original packaging for storing the pruning
shear 15, in the event of eventual dispatch thereof for
inspection or repair.
• Keep the tool out of the reach of children.
• When the pruning shear 15 is not used, close the
blade 17 and always set switch 07 to the "OFF"
position, in order to avoid bodily injury and deep battery
discharge 09.
• Never use the tool if it is damaged, improperly adjusted,
or mounted in an incomplete fashion.
• Pay attention to the projections that can cause physical
injuries or damage to property. The user and
bystanders must wear eye protection.
• Always wear appropriate shoes and clothing.
SAFETY MARKINGS
Do not use in rain.
The pruning shear is fragile, use
with caution.
Pruning shear in accordance
with CE standards.
The equipment must be used in
a temperature range between
-5°C (+23°F) and +30°C
(+86°F).

TECHNICAL SPECIFICATIONS

Cutting capacity:
Pruning shear power supply:
Average motor power:
pruning shear +
Depending on the type
of wood, 1 to 30 mm
(1.2 in.)
37 Volts
98 Watts
- 8 -
Pruning shear weight:
Acceleration to which upper
limbs are exposed according to
EN 50260-1: 2005 (value plus
K=1.5 m/s2):
Noise value measured according
to UE 2006/42/UE Directive;
according to ISO 3746:2010 +
ISO 11202:2012.
Sound pressure level measured
at the workstation (value plus
K=1.5 dB) ISO 4871:
INITIAL USE
1. Remove POWERPACK 03 from case 14.
2. Remove pruning shear 15 from case 14.
3. For FELCO 880 POWERPACK use, refer to FELCO 880
user manual found in case 14.
CAUTION
During initial use, if you try to work with your pruning
shear 15 without prior charging of the battery 09, the pruning
shear will not work. Refer to FELCO 880 user manual for the
procedure.
USE
Refer to the description of the tool on page 3 and illustration
A on page 4.
1. Connect the pruning shear 15 to the pruning shear power
cord 02.
2. Hold the pruning shear 15 in your hand, toggle switch 07
of the remote housing 06, from the "OFF" to the "ON"
position (the display 08 of the remote housing 06 is
activated).
3. Press once on trigger 16 and blade 17 opens. (Blade 17
opening and closing is proportional to the pressure
applied by the finger).
4. In order to stop the pruning shear 15, close the blade 17
using the trigger 16, keep the blade closed, toggle
switch 07 to the "OFF" position (the display 08 of the
remote housing 06 closes). It is possible to temporarily
pause the pruning shear using option "Stand-by Mode"
(Refer to FELCO 880 user manual).
NOTES
• In order to save the energy fed by battery 09 and to
also ensure maximum autonomy for the pruning
shear 15, consider using option "semi-opening" which is
adjustable to 50%, 60%, or 70%. (Refer to FELCO 880
user manual). This option offers precious time-saving
when pruning small diameters.
• If the wood is too thick, the pruning shears 15 stops in
the closing direction. Only opening is possible.
THE FIRST SHARPENING OPERATION AND THE BLADE
ADJUSTMENT MUST BE PERFORMED AFTER THE
FIRST HALF-HOUR OF USE!
745 g / 26.3 oz.
ah < 2.5 m/s2 max.
LpA < 70 dB