Felco 801-HP Manuel D'utilisation page 10

is necessary to disconnect the pruning shear 15 from the
power cord 02 before this operation.
REPLACING THE BLADE AND ANVIL BLADE
When the blade 17 has been replaced several times, and the
cut is less clean even after precise adjustment of the play
between the blade 17 and the anvil blade 18, it is time to
replace the anvil blade 18. To do so, refer to the illustration E
on page 6 of this user manual.
CAUTION
Never operate the pruning shear 15 during this operation, as
this may lead to the damage of the tool and personal injury. It
is necessary to disconnect the pruning shear 15 from the
power cord 02 before this operation.
SEMI-OPENING MODE
The user has the ability to set blade 17 to "semi-opening
mode" at any time. This can be useful when it is necessary to
cut small diameter wood and large opening is not necessary.
To activate semi-opening mode, simply activate the
trigger 16 twice very quickly and release it immediately.
Blade 17 is set to half of its full opening path. To return to
large opening mode, simply activate the trigger 16 twice
quickly again and blade 17 is repositioned to its normal
opening mode. This mode can be permanently disabled
using the remote control housing 06. To do this, refer to
FELCO 880 user manual. Semi-opening setting is also
possible using the remote control housing 06; this allows you
to set permanently the level of openness of the blade when
you press the semi-open option. To do this, refer to the
POWERPACK FELCO 880 user manual.
STAND-BY MODE OF THE PRUNING SHEAR
The standby mode of the pruning shear allows you to stop
the tool without having to activate switch 07. To enable this
mode, you simply activate the trigger 16 two times rapidly
and hold until you hear a set of three quick beeps. You can
then release trigger 16 and blade 17 shall not open. To open
the blade 17, simply press once on the trigger 16.
CAUTION
This option is not intended as a power down of the tool, but
only simply as an aid to the pruning process. Attention must
be paid as a movement of trigger 16 will trigger the opening
of the blade 17.
This mode can be permanently disabled using the remote
control housing 06. To do this, refer to FELCO 880 user
manual.
MISCELLANEOUS MAINTENANCE
Please refer to illustration F on page 83 of this user manual.
• Clean the cutting head at regular intervals using a
cleaner and lubricant that protects against corrosion
(i.e. spray FELCO 980). Remove especially all
accumulations of sap on the blade 17 and on the anvil
blade 18.
• Clean the tool body with a damp cloth on a regular
basis.
• Grease daily the grease tank of the anvil blade 18 by
applying grease using the grease pump FELCO 991, on
the grease bolt head 21.
• Do not leave pruning shear 15 on the ground, or
exposed to the weather.
• After 400'000 cuts, but at least once a year, it is
recommended to require a thorough inspection by an
authorized dealer, in order to increase the longevity of
your tool. The following parts will be replaced as a
preventive measure (Connecting rod, circlips, scraper
and back cover screws). The review fee shall be borne
by the end user.
OUTSIDE THE PRUNING PERIOD
• Store the pruning shear 15 in its case 14 protected
against heat, dust and moisture.
• It is recommended, during OFF SEASON period, to
perform a general inspection of your pruning shear 15,
at an authorized dealer. For more information, consult
your authorized dealer, or contact us.
• With regard to POWERPACK FELCO 880 storage,
refer to FELCO 880 user manual.
AUDIBLE NOTIFICATIONS
CAUTION
The user is helped by sound signals emitted by the control
housing 04 of POWERPACK FELCO 880. For the meaning
of these signals, it is necessary to refer to FELCO 880 user
manual.
INCIDENTS
If the pruning shear 15 do not work:
1. Set switch 07 of the remote control housing 06 to the
"ON" position.
2. Check the battery 09 charge, while watching the
display 08 of the remote control housing 06. If necessary,
charge the battery 09 according to the instructions in
FELCO 880 user manual.
3. If the pruning shear 15 continues not to operate, set
switch 07 of the remote control housing 06 to the "OFF"
position and verify that the power cord 02 is correctly
connected and that the connection plug 01 is tight. Set
switch 07 of the remote control housing 06 to the "ON"
position.
4. If the pruning shear still does not work, return pruning
shear FELCO 801-HP and POWERPACK FELCO 880 in
the original packaging to an authorized dealer.
GUARANTEE AND NON-RESPONSIBILITY CLAUSE
In the event of failure of a mechanical, electrical or electronic
part, and subject to standard and reasonable use, and if the
tool is maintained in accordance with the user manual,
FELCO SA guarantees its products to its end customers for a
period of 2 YEARS as of the date of delivery to the end
customer. This period may not exceed 18 months as of the
- 10 -