Dmx-512 Connection / Connection Between Fixtures - EuroLite TC-3 Mode D'emploi

DMX-512 connection / connection between fixtures

LIGHTING CONTROL
PROTOCOL DMX-512
Sensitivity
Blackout
Microphone
Setting the DMX-
DIP-switch no. 1 2 3 4 5 6 7 8 9
starting address:
Projector number
Starting address 1 2 4 8 16 32 64 128 256
& channels
On
Fuse:
Projector 1 - channel 1 DMX In
Off Off
T 2 A, 250 V
On
Projector 2 - channel 2
Off
On
Projector 3 - channel 3
Off
On
Projector 4 - channel 4
Off
On
Projector 5 - channel 5
Off
XLR occupation:
Power supply:
1: Ground
230 V AC, 50 Hz ~
2: Signal (–)
3: Signal (+)
DMX Out
Projector 1
Starting address 1
The wires must not come into contact with each other, otherwise
Only use a stereo shielded cable and 3-pin XLR-plugs and connectors in order to connect the controller with
the fixture or one fixture with another.
Occupation of the XLR-connection:
If you are using controllers with this occupation, you can connect the DMX-output of the controller directly
with the DMX-input of the first fixture in the DMX-chain. If you wish to connect DMX-controllers with other
XLR-outputs, you need to use adapter-cables.
Building a serial DMX-chain:
Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next fixture. Always
connect one output with the input of the next fixture until all fixtures are connected.
Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120
between Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture.
Occupation mono 1/4" jack-plug:
Tip
In Phase (+)
DMX-512 Controller
Sensitivity
Setting the DMX-
DIP-switch no.
starting address:
Projector number
Starting address
& channels
Fuse:
Projector 1 - channel 1
T 2 A, 250 V
Projector 2 - channel 2
Projector 3 - channel 3
Projector 4 - channel 4
Projector 5 - channel 5
Power supply:
230 V AC, 50 Hz ~
Starting address 2
the fixtures will not work at all, or will not work properly.
Sleeve
Ground
XLR-occupation:
DMX-output DMX-input
XLR mounting-socket: XLR mounting-plug:
1: Ground 1: Ground
2 1 1 2
2: Signal (–) 2: Signal (–)
3 3
3: Signal (+) 3: Signal (+)
LIGHTING CONTROL
PROTOCOL DMX-512
Blackout
Microphone
1 2 3 4 5 6 7 8 9
1 2 4 8 16 32 64 128 256
On
DMX In
Off Off
On
Off
On
Off
On
Off
On
Off
XLR occupation:
1: Ground
2: Signal (–)
3: Signal (+)
DMX Out
Projector 2
21
LIGHTING CONTROL
PROTOCOL DMX-512
Sensitivity
Blackout
Microphone
Setting the DMX-
DIP-switch no. 1 2 3 4 5 6 7 8 9
starting address:
Projector number
Starting address 1 2 4 8 16 32 64 128 256
& channels
On
Fuse:
Projector 1 - channel 1 DMX In
Off Off
T 2 A, 250 V
On
Projector 2 - channel 2
Off
On
Projector 3 - channel 3
Off
On
Projector 4 - channel 4
Off
On
Projector 5 - channel 5
Off
XLR occupation:
Power supply:
1: Ground
230 V AC, 50 Hz ~
2: Signal (–)
3: Signal (+)
DMX Out
Projector 3
Starting address 3
Ω
120 Ohms
resistor