Bosch GSB 1300 Professional Notice Originale page 12

12 | English
A)
(13) Universal bit holder
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Impact Drill
Article number
Rated power input
Power output
No-load speed
Impact rate at no-load speed
Rated torque
Clockwise/anti-clockwise ro-
tation
Spindle collar diameter
Max. drilling diameter
– Masonry
– Concrete
– Steel
– Wood
Chuck capacity
Weight according to
EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise/vibration information
Noise emission values determined according to
EN 62841-2-1.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 95 dB(A); sound power level
106 dB(A). Uncertainty K = 5 dB.
Wear hearing protection
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-1.
2
Drilling into metal: a = 7.5 m/s , K = 1.5 m/s
h
Impact drilling into concrete: a = 10.5 m/s
h
2
Screwdriving: a <2.5 m/s , K = 1.5 m/s
h
2
Thread cutting: a < 2.5 m/s , K = 1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
1 609 92A 55G | (01.07.2019)
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
GSB 1300
Implement additional safety measures to protect the oper-
3 601 AA1 0..
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
W 550
and organising workflows correctly.
W 270
-1
min 0–2 800
Assembly
-1
min 0–44 800
u
Nm 1.5
●
Auxiliary Handle (see figure A)
mm 43
u
mm 13
u
mm 13
mm 10
Turn the wing bolt (7) anti-clockwise and guide the auxiliary
mm 25
handle (8) in the required position over the drill chuck onto
mm 1.5–13
the spindle collar of the power tool.
You can swivel the auxiliary handle (8) in order to achieve a
kg 1.8
safe work posture that minimises your fatigue.
Swivel the auxiliary handle (8) to the required position and
/ II
retighten the wing bolt (7) in clockwise direction.
Setting the Drilling Depth
You can use the depth stop (9) to set the required drilling
depth X.
Loosen the wing bolt for adjusting the depth stop (6) and in-
sert the depth stop into the auxiliary handle (8).
The fluting on the depth stop (9) must face upwards.
Pull the depth stop far enough out that the distance between
the drill bit tip and the edge of the depth stop corresponds
to the required drilling depth X.
Retighten the wing bolt for adjusting the depth stop (6).
Changing the Tool
2
2 2
u
, K = 1.5 m/s
2
2
Keyed chuck (see figure B)
Open the keyed chuck (1) by turning it until the tool can be
inserted. Insert the tool.
Insert the drill chuck key (11) into the corresponding holes
of the keyed chuck (1) and clamp the tool evenly.
Screwdriving tools (see figure C)
You should always use a universal bit holder (13) when using
screwdriver bits (12). Only use screwdriver bits that fit the
screw head.
Pull the plug out of the socket before carrying out any
work on the power tool.
Before carrying out any work, make sure that the wing
bolt is tightened. Loss of control can cause personal in-
jury.
Do not operate your power tool without the auxiliary
handle (8).
Wear protective gloves when changing tools. The drill
chuck may heat up significantly when it is used for long
periods.
Bosch Power Tools