Use And Maintenance - V-ZUG DF-L5 Manuel D'utilisation

• Fixing the hood to the lower part of the wall cabinet
Position fastening template A to the bottom of the cabinet
(Fig.1) taking into account the minimum distance from the hob.
- Fasten the 4 screws C, without screwing them in all the way.
- Position the hood under the cabinet and push it all the way
against the wall, screw in/tighten the 4 screws C.
- Adjust spacer L from screws P (fig.2) so that the back of the
appliance is against the cabinet.
• Extraction through an outside wall
The appliance expels the fumes through an outside wall or a
duct. It is necessary to buy a telescopic pipe in accordance
with the standards in use (inflammable) and connect it to
flange B (Fig 3).
• Recirculation
To transform the cooker hood from the extraction version
to the re circulating one ask your supplier for an activated
carbon filter.
The filter must be fitted to the extracting group cooker hood
in the centre of the fan grille by twisting it by 90 degrees until
it is gripped securely (Fig 6). For this operation remove the
anti-grease filter(s) G (Fig 5). The clean air is returned into the
room through a connecting tube passing inside the cupboard
and connected to the ring B (fig 4).

USE AND MAINTENANCE

• We recommend that the cooker hood is switched on before
any food is cooked. We also recommend that the appliance is
left running for 15 minutes after the food is cooked, in order
to thoroughly eliminate all contaminated air.
The effective performance of the cooker hood depends on
constant maintenance; the anti-grease filter and the active
carbon filter both require special attention.
• The anti-grease filter is responsible retaining the grease
particles suspended in the air, therefore it is subject to clogging
with variable frequency according to the use of the appliance.
- To prevent the danger of possible fires, at least every 2
months one must wash the anti-grease filters by hand using
non-abrasive neutral liquid detergents or in the dishwasher at
low temperatures and on short cycles.
- After a few washes, colour alterations may occur. This does
not give the right to claim their replacement.
• The active carbon filters are used to purify the air that is
sent back into the room and its function s to mitigate the
unpleasant odours produced by cooking.
- The non-regenerable active carbon filters must be replaced
at least every 4 months. The saturation of the active charcoal
depends on the more or less prolonged use of the appliance,
on the type of kitchen and on the frequency with which anti-
grease filter is cleaned.
- Regenerable active charcoal filters must be washed by hand,
with non abrasive neutral detergents, or in the dishwasher at
a maximum temperature of 65°C (the washing cycle must be
complete without dishware). Remove excess water without
damaging the filter, remove the plastic parts, and let the mat
dry in the oven for at least 15 minutes approximately at a
maximum temperature of 100°C. To keep the regenerable
charcoal filter functioning efficient this operation must be
repeated every 2 months. These must be replaced at least
every 3 years or when the mat is damaged.
• Before remounting the anti-grease filters and the rege-
nerable active charcoal filters it is important that they are
completely dry.
• Clean the hood frequently, both internally and externally,
using a cloth dampened with denatured alcohol or neutral
liquid detergents that are non abrasive.
• The lighting .system is designed for use during cooking
and not for the prolonged general lighting of the room. The
prolonged use of the lighting system significantly decreases
the average duration of the bulbs.
• Attention: The non compliance with the hood cleaning
warnings and with the replacement and cleaning of the filters
entails risk of fires. One therefore recommends keeping to the
suggested instructions.
• Commands: (Fig.7) the key symbols are explained below:
This hood is fitted with a microswitch which allows the
activation of the motor speed) through the opening of the
telescopic undercarriage. If the telescopic undercarriage is
closed the motor speeds cannot be activated.
This microswitch does not have an impact on the activation of
the lights which must be switched on through the appropriate
switch (see fig.7A).
A = Light switch
A1 = Off key
A2 = On key
B = Speed control
B1 = FIRST SPEED key
B2 = SECOND SPEED key
B3 = THIRD SPEED ke
Warning! If the telescopic undercarriage is closed with
the speed set at 2,, once it is re-opened, the hood will be
reactivated with the same speed in use when the hood was
closed.
• Replacing the halogen/incandescent lamps (Fig.8A):
Only use lamps of the same type and wattage installed on
the device.
• Replacing LED lamps (Fig.8B):
If the appliance version is with LED lamps, the intervention of
a specialised technician is necessary to replace them.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY
FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE
ABOVE WARNINGS.
- 14 -