Use And Maintenance - V-ZUG DW-S6 Manuel D'utilisation

hood is to be xed.
• Fixing the decorative telescopic flue:
-Arrange the electrical power supply within the dimensions
of the decorative ue. If your appliance is to be installed in the
ducting version or in the version with external motor, prepare
the air exhaust opening.
-Adjust the width of the support bracket of the upper ue
(Fig.3).
-Then x it to the ceiling using the screws A (Fig.3) in such a
way that it is in line with your hood and respecting the distance
from the ceiling indicated in Fig.2.
-Connect the ange C to the air exhaust hole using a connec-
tion pipe (Fig.4).
-Insert the upper ue into the lower ue.
-Fix the lower ue to the hood using the screws B provided
(Fig.4), extract the upper ue up to the bracket and x it with
the screws B (Fig.3).
-To transform the hood from a ducting version into a ltering
version, ask your dealer for the charcoal lters and follow the
installation instructions.
• Filter hood:
Please note:
In order to transform the hood from EXTRACTOR HOOD
into FILTER HOOD the carbon lters must be ordered at your
distributor as accessory.
-To replace the extractable active carbon filters X, pull lever
outwards as shown in Fig.6.
-There are two types of charcoal lters: regenerable (washable)
(Fig.7) and non-regenerable (Fig.6).

USE AND MAINTENANCE

• We recommend that the cooker hood is switched on before
any food is cooked. We also recommend that the appliance is
left running for 15 minutes after the food is cooked, in order
to thoroughly eliminate all contaminated air.
The e ective performance of the cooker hood depends on
constant maintenance; the anti-grease lter and the active
carbon lter both require special attention.
• The anti-grease filter is responsible retaining the grease
particles suspended in the air, therefore it is subject to
clogging with variable frequency according to the use of the
appliance.
- To prevent the danger of possible res, at least every 2
months one must wash the anti-grease lters by hand using
non-abrasive neutral liquid detergents or in the dishwasher
at low temperatures and on short cycles.
- After a few washes, colour alterations may occur. This does
not give the right to claim their replacement.
• The active carbon filters are used to purify the air that is
sent back into the room and its function s to mitigate the
unpleasant odours produced by cooking.
- The non-regenerable active carbon lters must be replaced
at least every 4 months. The saturation of the active charcoal
depends on the more or less prolonged use of the appliance,
on the type of kitchen and on the frequency with which anti-
grease lter is cleaned.
- Regenerable active charcoal lters must be washed by hand,
with non abrasive neutral detergents, or in the dishwasher at
a maximum temperature of 65°C (the washing cycle must be
complete without dishware). Remove excess water without
damaging the lter, remove the plastic parts, and let the mat
dry in the oven for at least 15 minutes approximately at a
maximum temperature of 100°C. To keep the regenerable
charcoal lter functioning e cient this operation must be
repeated every 2 months. These must be replaced at least
every 3 years or when the mat is damaged.
• Before remounting the anti-grease filters and the rege-
nerable active charcoal lters it is important that they are
completely dry.
• Clean the hood frequently, both internally and externally,
using a cloth dampened with denatured alcohol or neutral
liquid detergents that are non abrasive.
• The lighting .system is designed for use during cooking
and not for the prolonged general lighting of the room. The
prolonged use of the lighting system signi cantly decreases
the average duration of the bulbs.
• Attention: The non compliance with the hood cleaning
warnings and with the replacement and cleaning of the lters
entails risk of res. One therefore recommends keeping to the
suggested instructions.
• Replacing halogen light bulbs (Fig.8):
To replace the halogen light bulbs B, remove the glass panel
C using a lever action on the relevant cracks.
Replace the bulbs with new ones of the same type.
Caution: Do not touch the light bulb with bare hands.
• Commands (Fig.9):
The key symbols are explained below:
A = LIGHT
B = OFF
C = SPEED I
D = SPEED II
E = SPEED III
F = AUTOMATIC STOP TIMER - 15 minutes (*)
• If your appliance does not have the INTENSIVE speed
function, press key E for two seconds and it will be activated
for 10 minutes after which it will return to the previously set
speed.
When the function is active the LED ashes. To interrupt it
before the 10 minutes have expired press key E again.
• Clean Air:
By pressing key F for two seconds (with the hood switched
o ) the "clean air" function is activated.
This function switches the appliance on for ten minutes every
hour at the rst speed.
As soon as this function is activated the motor starts up at the
rst speed for ten minutes.
During this time key F and key C must ash at the same time.
After ten minutes the motor switches o and the LED of key
F remains switched on with a xed light until the motor starts
up again at the rst speed after fty minutes and keys F and
C start to ash again for ten minutes and so on.
By pressing any key for the exclusion of the hood light the
hood will return immediately to its normal functioning (e.g.
if key D is pressed the "clean air" function is deactivated and
the motor moves to the 2nd speed straight away.
By pressing key B the function is deactivated).
(*) The "AUTOMATIC STOP TIMER" delays stopping of the
hood, which will continue functioning for 15 minutes at the
operating speed set at the time this function is activated.
• Anti-grease and active carbon filters saturation:
-After 30 hours of work, the key A ashes every 2 sec.; in that
event, the anti-grease and active carbon lter must be cleaned,
if present.
-After 120 hours of work, the key A ashes every 0.5 sec.; in
- 16 -