Télécharger Imprimer la page

Without A Pc; Configuration - AKO 15740 Manuel D'utilisation

Masquer les pouces Voir aussi pour 15740:

Publicité

Les langues disponibles

Les langues disponibles

5.- Connectivity
5.- Connectivity
5.- Connectivity
5.- Connectivity
5.- Connectivity
This unit has a port for connecting RS485 (MODBUS) data, enabling it to communicate with other AKO units and
This unit has a port for connecting RS485 (MODBUS) data, enabling it to communicate with other AKO units and
This unit has a port for connecting RS485 (MODBUS) data, enabling it to communicate with other AKO units and
This unit has a port for connecting RS485 (MODBUS) data, enabling it to communicate with other AKO units and
This unit has a port for connecting RS485 (MODBUS) data, enabling it to communicate with other AKO units and
even to control them via a PC. There are two possible connection modes.
even to control them via a PC. There are two possible connection modes.
even to control them via a PC. There are two possible connection modes.
even to control them via a PC. There are two possible connection modes.
even to control them via a PC. There are two possible connection modes.

5.1- Without a PC

5.1- Without a PC
5.1- Without a PC
5.1- Without a PC
5.1- Without a PC
The units must be CAMRegis or AKOCAM and it is possible to connect a maximum of 7 units, one in master mode
The units must be CAMRegis or AKOCAM and it is possible to connect a maximum of 7 units, one in master mode
The units must be CAMRegis or AKOCAM and it is possible to connect a maximum of 7 units, one in master mode
The units must be CAMRegis or AKOCAM and it is possible to connect a maximum of 7 units, one in master mode
The units must be CAMRegis or AKOCAM and it is possible to connect a maximum of 7 units, one in master mode
and the rest in slave mode.
and the rest in slave mode.
and the rest in slave mode.
and the rest in slave mode.
and the rest in slave mode.
MASTER
Logger
Tr- Tr
Gnd
+
21 22 23
The master can display the data of any of the units connected to it and print them if the unit has a printer (it is
The master can display the data of any of the units connected to it and print them if the unit has a printer (it is
The master can display the data of any of the units connected to it and print them if the unit has a printer (it is
The master can display the data of any of the units connected to it and print them if the unit has a printer (it is
The master can display the data of any of the units connected to it and print them if the unit has a printer (it is
recommended to use an AKO-15742, 15752 or 15782 as master).
recommended to use an AKO-15742, 15752 or 15782 as master).
recommended to use an AKO-15742, 15752 or 15782 as master).
recommended to use an AKO-15742, 15752 or 15782 as master).
recommended to use an AKO-15742, 15752 or 15782 as master).

Configuration

Configuration
Configuration
Configuration
Configuration
Slave equipment: Must be in slave mode (See chapter 4.1) and have a different slave address (MODBUS)
Slave equipment: Must be in slave mode (See chapter 4.1) and have a different slave address (MODBUS)
Slave equipment: Must be in slave mode (See chapter 4.1) and have a different slave address (MODBUS)
Slave equipment: Must be in slave mode (See chapter 4.1) and have a different slave address (MODBUS)
Slave equipment: Must be in slave mode (See chapter 4.1) and have a different slave address (MODBUS)
configured for each unit. This address must be between 1 and 247.
configured for each unit. This address must be between 1 and 247.
configured for each unit. This address must be between 1 and 247.
configured for each unit. This address must be between 1 and 247.
configured for each unit. This address must be between 1 and 247.
Master equipment: Must be in master mode. To each of the 6 external inputs will be assigned the address of
Master equipment: Must be in master mode. To each of the 6 external inputs will be assigned the address of
Master equipment: Must be in master mode. To each of the 6 external inputs will be assigned the address of
Master equipment: Must be in master mode. To each of the 6 external inputs will be assigned the address of
Master equipment: Must be in master mode. To each of the 6 external inputs will be assigned the address of
each of the slaves connected to it (configured in the previous step).
each of the slaves connected to it (configured in the previous step).
each of the slaves connected to it (configured in the previous step).
each of the slaves connected to it (configured in the previous step).
each of the slaves connected to it (configured in the previous step).
Display external data (only master unit)
Display external data (only master unit)
Display external data (only master unit)
Display external data (only master unit)
Display external data (only master unit)
On accessing the logger's menu (see chapter 3.3.1) a screen will appear with the list of connected units.
On accessing the logger's menu (see chapter 3.3.1) a screen will appear with the list of connected units.
On accessing the logger's menu (see chapter 3.3.1) a screen will appear with the list of connected units.
On accessing the logger's menu (see chapter 3.3.1) a screen will appear with the list of connected units.
On accessing the logger's menu (see chapter 3.3.1) a screen will appear with the list of connected units.
The "Local Inputs" option allows you to display the data of the unit's own inputs.
The "Local Inputs" option allows you to display the data of the unit's own inputs.
The "Local Inputs" option allows you to display the data of the unit's own inputs.
The "Local Inputs" option allows you to display the data of the unit's own inputs.
The "Local Inputs" option allows you to display the data of the unit's own inputs.
Select a unit, press SET and follow the steps described in point 3.3.1 to obtain or print the data recorded for the
Select a unit, press SET and follow the steps described in point 3.3.1 to obtain or print the data recorded for the
Select a unit, press SET and follow the steps described in point 3.3.1 to obtain or print the data recorded for the
Select a unit, press SET and follow the steps described in point 3.3.1 to obtain or print the data recorded for the
Select a unit, press SET and follow the steps described in point 3.3.1 to obtain or print the data recorded for the
selected unit.
selected unit.
selected unit.
selected unit.
selected unit.
SLAVE 1
SLAVE 2
Logger
Logger
Tr- Tr
Gnd
Tr- Tr
Gnd
+
+
21 22 23
21 22 23
RS-485
(MODBUS)
SET
SET
Own
inputs
External
inputs
34
SLAVE 6
Logger
Tr- Tr
Gnd
+
21 22 23
Input No.

Publicité

loading

Ce manuel est également adapté pour:

1575015780157421575215782