Technical Data; Noise/Vibration Information; Dust/Chip Extraction - Bosch GSH 5 Professional Notice Originale

12 | English

Technical Data

Demolition hammer
Article number
Rated power input
Impact rate
Chisel positions
Impact energy per stroke
according to EPTA-Proced-
ure 05:2016
Tool holder
Lubrication
Weight according to EPTA-
Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.

Noise/Vibration Information

Noise emission values determined according to
EN 60745-2-6.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 89 dB(A); sound power level
100 dB(A). Uncertainty K=3 dB.
Wear hearing protection
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to
EN 60745-2-6:
2
Chiselling: a = 12 m/s , K = 1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
Pull the plug out of the socket before carrying out any
u
work on the power tool.
1 609 92A 5JE | (13.12.2019)
Auxiliary handle (see figure A)
GSH 5 u
3 611 C38 7..
You can swivel the auxiliary handle (7) to any angle for a safe
W 1100
work posture that minimises fatigue.
-1
min 2900
– Loosen the knurled nut (8), rotate the auxiliary handle (7)
12
J 7.5
The auxiliary handle (7) can be refitted in a different posi-
tion.
– To do this, completely unscrew the knurled nut (8) and
SDS max
Grease lubrication
– Pull off the auxiliary handle (7) to the side and rotate the
kg 5.8
– Fit the auxiliary handle (7) by following the steps in re-
/ II
Changing the Tool
With the SDS-max tool holder, you can change the applica-
tion tool simply and easily without additional aids.
The dust protection cap (1) largely prevents the penetration
of drilling dust into the tool holder during operation. When
inserting the tool, make sure that the dust protection cap (1)
does not become damaged.
u
Inserting the application tool (see figure B)
– Clean and lightly grease the shank of the application tool.
2
– Insert the application tool into the tool holder while turn-
– Check that it is locked by pulling on the tool.
Removing the application tool (see figure C)
– Push the locking sleeve (2) back and remove the applica-

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
Do not operate your power tool without the auxiliary
handle (7).
around the axis of the tool to the required position and
retighten the knurled nut (8).
then pull the hexagon bolt upwards and out.
remaining clamping element by 180°.
verse order.
Replace a damaged dust protection cap immediately.
It is recommended that you have use an after-sales
service for this.
ing it until it locks automatically.
tion tool.
Bosch Power Tools