Bosch GBH 18V-45 C Professional Notice Originale page 21

Working mode (18) indic- Functions
ator
In Favourite working mode, the power tool can be individually configured via a smartphone.
lights up
– "Hammer drilling" operating mode: Increase in speed can be configured in multiple speed
– Electronic Precision Control (EPC) is always active, final speed and start-up speed can be
– "Chiselling" operating mode: Adaptive Speed Control can be switched on and off
– Sensitivity of the rapid shut-off (KickBack Control) can be configured
Connectivity functions
In conjunction with the GCY 42 Bluetooth® Low Energy Mod-
ule, the following connectivity functions are available for the
power tool:
– Registration and personalisation
– Status check, output of warning messages
– General information and settings
– Management
Read the corresponding operating instructions for informa-
tion about the Bluetooth® Low Energy Module GCY 42.
The smartphone indicator (21) lights up if the power tool
sends information (e.g. a temperature warning) to a mobile
device via Bluetooth® wireless technology.
Practical Advice
With the Bluetooth® Low Energy Module GCY 42, the
u
power tool is equipped with a radio interface. Local
operating restrictions, e.g. in aircraft or hospitals,
must be observed.
In areas where the Bluetooth® wireless technology is
u
not allowed to be used, the Bluetooth® Low Energy
Module GCY 42 and the button cell must be removed.
Note: The cover (15) can only be securely closed if the
Bluetooth® Low Energy Module GCY 42 and the button cell
are situated in the power tool.
– To deactivate the Bluetooth® Low Energy Module
GCY 42, rotate the button cell or place means of insula-
tion between the button cell and Bluetooth® Low Energy
Module GCY 42.
– Close the cover (15) to prevent dirt from getting in.
Changing the chiselling position (Vario-Lock)
You can lock the chisel in 16 different positions, allowing
you to select the optimum working position for each task.
– Insert the chisel into the tool holder.
– Turn the mode selector switch (5) to the "drilling" posi-
tion.
– Turn the application tool to the required chisel position.
– Turn the mode selector switch (5) to the "chiselling" posi-
tion. With this, the tool holder is locked.
Chiselling with lock function
To chisel for extended periods without pressing the on/off
switch (9), lock the on/off switch in "chiselling" operating
mode.
Bosch Power Tools
settings
configured
– To lock the power tool, press the on/off switch (9) down
– To switch the lock off, press the lock-on button (7) again.
Note: If you switch to a different operating mode while the
on/off switch is locked, the power tool will switch off.
Vibration damping
u
Recommendations for Optimal Handling of the Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Maintenance and Service
Maintenance and Cleaning
u
u
u
Clean the tool holder (2) after each use.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
fully whilst simultaneously pressing the lock-on
switch (7).
The integrated vibration damping function re-
duces the generated vibration.
Do not continue to use the power tool if the damping
element is damaged.
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
the power tool and the ventilation slots clean.
Replace a damaged dust protection cap immediately.
It is recommended that you have use an after-sales
service for this.
1 609 92A 53R | (22.10.2019)
English | 21