Operation - EINHELL TE-MG 300 EQ Instructions D'origine

in tool.
•
The equipment comes with a disk (14) for
safely securing plug-in tools with recesses.
Please note the correct use (camber facing
the tool) of the disk (14) for plug-in tools with
recess as shown in Fig. 8 and 9.
Check that the plug-in tool is secure.
5.2 Triangular sanding/grinding plate
Fit the triangular sanding/grinding plate to use the
equipment as a delta sander/grinder.
5.2.1 Fastening the sanding/grinding paper
The Velcro fastener enables easy changing of
sanding/grinding paper. Make sure that the va-
cuum extraction holes on the sanding/grinding
paper and the sanding/grinding disk are aligned.
5.3 Fitting the dust extraction device
(Fig. 4/5/6)
The dust extraction device prevents the accumu-
lation of dirt and high dust loads in the air, and it
makes it easier to dispose of the dust.
•
Open the quick-release lock for changing
tools and place the equipment in a stable po-
sition as described in 5.1.
•
Mount the dust extraction device (6a) on the
tool chuck (2) as shown in Fig. 4.
•
Fasten the dust extraction device (6a) with
the fastening clip (6b) by latching it in the air
vents of the equipment as shown in Fig. 5.
•
Connect the extractor adapter (3) to the dust
extraction device (6a). Make sure that the ar-
row (A) on the extractor device coincides with
the recess (B) on the dust extraction device
(6a) (see Fig. 5). Turn the extractor adapter
(3) anti-clockwise until it engages..
•
Connect your tool to an extraction unit or va-
cuum cleaner. This will provide excellent ext-
raction of chips and dust from the workpiece.
The benefi ts are that you will protect both the
equipment and your own health. Your work area
will also be clean and safe.
Anl_TE_MG_300_EQ_SPK7.indb 20 Anl_TE_MG_300_EQ_SPK7.indb 20
GB

6. Operation

6.1 Switching on/off
Slide the switch (1) forwards to switch on the
equipment.
Slide the switch (1) to the rear to switch off the
equipment.
6.2 Practical tips
•
Switch on the equipment.
•
Work away from the body.
•
Never move your hands into the direct vicinity
of the work area.
•
Use only plug-in tools which are in good wor-
king order and undamaged.
Plug-in tools
Sawing: Sawing wood and plastic.
Notes on working practice: When sawing, watch
out for foreign bodies in the workpiece and remo-
ve these if necessary. Plunge cutting is allowed
only in soft materials such as wood or plaster-
board.
Sanding/grinding: Surface sanding/grinding at
edges, in corners or hard-to-reach areas. Depen-
ding on choice of sanding/grinding paper for the
sanding/grinding of wood, paint, lacquer, etc.
Notes on working practice: This equipment off ers
particularly high performance for the sanding/
grinding of hard-to-reach corners and edges. To
sand/grind profi les and channels you can also
work with just the tip or the edge of the sanding/
grinding disk. Various sanding/grinding papers
are available, specially designed for the diff erent
types of material you may be working on and the
amount you wish to remove from the surface.
The amount removed will depend largely on the
choice of sanding/grinding paper and pressure
applied to the sanding/grinding disk.
Scraping: Scraping off old paint or adhesives.
Notes on working practice: Move the plug-in tool
against the area you want to remove. Begin with
a fl at angle of incidence and little pressure. The
surface (e.g. wood, plaster) may be damaged if
too much pressure is used.
- 20 -
05.07.2016 08:42:09 05.07.2016 08:42:09