EINHELL VARRITO 44.651.60 Instructions D'origine page 19

The tool chuck (2) is magnetic in order to
secure the plug-in tool during the clamping
procedure.
•
Close the quick-release lock for changing
tools (5) again. Take care that the pins of the
chuck (2) remain in the recesses in the plug-
in tool.
•
The equipment comes with a disk (14) for
safely securing plug-in tools with recesses.
Please note the correct use (camber facing
the tool) of the disk (14) for plug-in tools with
recess as shown in Fig. 4 and 5.
Check that the plug-in tool is secure.
5.2 Triangular sanding/grinding plate
Fit the triangular sanding/grinding plate to use the
equipment as a delta sander/grinder.
5.2.1 Fastening the sanding/grinding paper
The Velcro fastener enables easy changing of
the abrasive paper. Make sure that the vacuum
extraction holes on the abrasive paper and the
grinding/sanding disk are aligned.
6. Operation
6.1 Charging the LI battery pack (Fig. 6/7)
1. Remove the battery pack (6) from the handle,
pressing the pushlock button (7) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the socket outlet. The green LED will then
begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
Anl_Varrito_SPK9.indb 19 Anl_Varrito_SPK9.indb 19
GB
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the power of the multifunction tool
drops. Never allow the battery pack to become
fully discharged. This will cause it to develop a
defect.
6.2 Switching on and off (Fig. 8)
Slide the switch (1) forwards to switch on the
equipment.
Slide the switch (1) to the rear again to switch off
the equipment.
6.3 Practical tips
•
Switch on the equipment.
•
Work away from the body.
•
Never move your hands into the direct vicinity
of the work area.
•
Use only plug-in tools which are in good wor-
king order and undamaged.
Plug-in tools:
Sawing: Sawing wood and plastic.
Notes on working practice: When sawing, watch
out for foreign bodies in the material and remove
them if necessary.
Plunge cutting is allowed only in soft materials
such as wood or plasterboard.
Sanding/grinding: Surface sanding/grinding at
edges, in corners or hard-to-reach areas. Depen-
ding on choice of abrasive paper for the sanding/
grinding of wood, paint, lacquer, etc.
Notes on working practice:
This equipment off ers particularly high perfor-
mance for the grinding/sanding of hard-to-reach
corners and edges. To grind/sand profi les and
channels you can also work with just the tip or
the edge of the grinding/sanding disk. Various
grinding/sanding papers are available, specially
designed for the diff erent types of material you
may be working on and the amount you wish to
remove from the surface. The amount removed
will depend largely on the choice of sanding/grin-
ding paper and pressure applied to the sanding/
grinding disk.
Scraping: Scraping off old paint or adhesives.
Notes on working practice:
Move the plug-in tool against the area you want to
remove. Begin with a fl at angle of incidence and
little pressure. The surface (e.g. wood, plaster)
may be damaged if too much pressure is used.
- 19 -
30.01.2018 15:31:36 30.01.2018 15:31:36