Bosch GAS 35 M AFC Professional Notice Originale page 19

OBJ_BUCH-1715-004.book Page 19 Monday, December 12, 2016 1:45 PM
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ECS,
70538 Stuttgart, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ECS
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Noise Information
Sound emission values determined according to
EN 60335-2-69.
Typically the A-weighted sound pressure level of the vacuum
cleaner is lower than 70 dB(A). Uncertainty K= 3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Technical Data
Wet/dry vacuum cleaner
Article number 3 601 JC3 ...
Rated voltage V 220–240**
Rated power input W
Frequency Hz
Container volume (gross) l
Net volume (for fluids) l
Dust bag contents l
Max. vacuum*
– Vacuum cleaner hPa
– Turbine hPa
Max. flow rate*
– Vacuum cleaner l/s
3
m /s
– Turbine
l/s
3
m /s
Max. vacuum capacity W
2
Surface of flat-fold filter m
Dust category
Weight according to EPTA-
Procedure 01:2014 kg
Protection class
Degree of protection
*Measured with a Ø 35 mm and 5 m long vacuum hose
**The values given are valid for nominal voltages [U] of 230 V. For lower
voltage and models for specific countries, these values can vary.
Bosch Power Tools
Automatic Start/Stop feature*
Rated voltage
EU 220–240 V
UK
UK
CH
* Specification of the allowable load of the connected power tool
(country-specific)
Assembly
 Before any work on the vacuum cleaner itself, pull the
mains plug.
Mounting the Vacuum-hose Holder (see figure A)
– Slide the vacuum-hose holders 4 firmly from above into the
retainers 32 intended for this purpose, until they engage.
Mounting the Vacuum Hose (see figure B)
– Mount the vacuum hose 24 onto the hose connection
piece 3 and turn it in clockwise direction to the stop.
GAS 35 M AFC
Note: While vacuuming, an electrostatic charge develops in
the vacuum hose and accessories caused by the friction of the
... 1.. ... 170
dust, which the operator could experience in the form of stat-
110
ic discharging (dependent on environmental influences and
1200 1000
physical perception).
50-60 50-60
As a general rule, Bosch recommends using an anti-static vac-
uum hose (accessory) when vacuuming fine dusts and dry
35 35
materials.
19 19
Mounting VAC Accessories (see figure C)
19 19
The vacuum hose 24 is equipped with a clip system, with
230 211
which the VAC accessories (tool sleeve 22, elbow 23) can be
254 242 connected.
Mounting the Tool Sleeve
36 31
– Mount the tool sleeve 22 onto the vacuum hose 24 until
0.036 0.031
both snap-fasteners 33 of the vacuum hose can be heard
74 71
to engage.
0.074 0.071 – To disassemble, press both snap-fasteners 33 inward and
pull the components apart.
1380 1150
Mounting Nozzles and Tubes
0.615 0.615
– Mount the elbow 23 onto the vacuum hose 24 until both
M M
snap-fasteners 33 of the vacuum hose can be heard to en-
gage.
12.4 12.4
– Afterwards, mount the desired VAC accessory (floor noz-
/I /I
zle, crevice nozzle, vacuum tube, etc.) firmly onto the el-
IP X4 IP X4
bow 23.
– To disassemble, press both snap-fasteners 33 inward and
pull the components apart.
Inserting/Removing a Disposal Bag or Dust
Bag (Dry Vacuuming) (see figures D1 – D2)
For dry vacuuming of materials according to dust category M,
a disposal bag 25 or a dust bag must be inserted.
English | 19
max. power min. power
output output
2200 W 100 W
110 V 750 W 100 W
240 V 1800 W 100 W
230 V 1100 W 100 W
1 609 92A 2N3 | (12.12.16)