HEIDENHAIN GAGE-CHEK 2000 Guide D'installation page 24

5.5 Connecting touch probes
The following touch probes can be connected
to the unit:
HEIDENHAIN TS 248 touch probe
HEIDENHAIN KT 130 edge finder
Renishaw touch trigger probe
Further information:
accessories", Page 21
Comply with the pin layout
"X113", Page 183
Further information:
Remove and save the dust protection cap
Route the cables depending on the mounting variant
"Assembly of the product", Page 23
Further information:
Connect the touch probe firmly
Further information: "Product overview", Page 25
If the cable connectors include mounting screws, do
not overtighten them
5.6 Wiring switching inputs and outputs
Depending on the peripherals to be
connected, the connection work may need to
be carried out by an electrical specialist.
Example: Safety Extra Low Voltage (SELV)
exceeded
Further information:
Page 20
The product fulfills the requirements of
standard IEC 61010-1 only if the power to
the peripheral devices is supplied from a
secondary circuit with current limitation as per
IEC 61010-1
3rd Ed.
limitation as per IEC 60950-1
2.5 or from a Class 2 secondary circuit as
specified in UL1310.
In place of IEC 61010-1
corresponding sections of standards DIN EN
61010-1, EN 61010-1, UL 61010-1 and CAN/
CSA-C22.2 No. 61010-1can be used, and, in
place of IEC 60950-1
corresponding sections of standards DIN EN
60950-1, EN 60950-1, UL 60950-1, CAN/CSA-
C22.2 No. 60950-1 can be applied.
Wire switching inputs and outputs in accordance with
the pin layout
"X113", Page 183
Further information:
Remove and save the dust protection cap
Route the cables depending on the mounting variant
"Assembly of the product", Page 23
Further information:
26
"Items supplied and
"Personnel qualification",
, Section 9.4 or with power
, Section
2nd Ed.
, Section 9.4, the
3rd Ed.
, Section 2.5, the
2nd Ed.
Connect the connecting cables of the peripherals
tightly to their connectors
Further information: "Product overview", Page 25
If the cable connectors include mounting screws, do
not overtighten them
The digital or analog inputs and outputs must
be assigned in the device settings of the
respective switching function.
5.7 Connecting a printer
Connecting a USB printer
Comply with the pin layout
Further information: "USB", Page 182
Remove and save the dust protection cap
Route the cables based on the mounting variant
Further information: "Assembly of the product", Page 23
Connect USB printer to USB Type-A port (X32). Make
sure the USB cable connector is fully inserted
Further information: "Product overview", Page 25
Connecting an Ethernet printer
Comply with the pin layout
Further information: "RJ45", Page 183
Remove and save the dust protection cap
Route the cables based on the mounting variant
Further information: "Assembly of the product", Page 23
Connect the Ethernet printer to the Ethernet port X116
using a standard CAT.5 cable. The cable connector
must firmly engage in the port
Further information: "Product overview", Page 25
5.8 Connecting input devices
Comply with the pin layout
Further information: "USB", Page 182
Remove and save the dust protection cap
Route the cables based on the mounting variant
Further information: "Assembly of the product", Page 23
Connect USB mouse or USB keyboard to USB Type-A
port (X32). Make sure the USB cable connector is fully
inserted
Further information: "Product overview", Page 25
5.9 Connecting a network peripheral
Comply with the pin layout
"RJ45", Page 183
Further information:
Remove and save the dust protection cap
Route the cables depending on the mounting variant
"Assembly of the product", Page 23
Further information:
Connect the network peripheral to Ethernet port X116
using a standard CAT.5 cable. The cable connector
must firmly engage in the port
Further information: "Product overview", Page 25
HEIDENHAIN | GAGE-CHEK 2000 | Installationsanleitung | 12/2018