Husqvarna 325R Manuel D'utilisation page 13

Masquer les pouces Voir aussi pour 325R:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 157
Do not touch the engine or the muffler when then
engine is on. Do not touch the engine or the muffler
for a while after the engine stops. Hot surfaces can
cause injuries.
A hot muffler can cause a fire. Be careful, if you use
the product near flammable liquids or fumes.
Do not touch the parts in the muffler, if the muffler is
damaged. The parts can contain some carcinogenic
chemicals.
Locknut
The locknut is used to lock some types of cutting
attachment.
(Fig. 23)
When you install the locknut, tighten it in the opposite
direction to operation direction of the cutting attachment.
Harness release function
WARNING: Do not use the harness if the
release function is defective. Make sure that
the harness release function operates
correctly when you adjust the product.
The harness release function is at the front of the
product. The harness straps must always stay at the
correct position.
(Fig. 24)
In an emergency, the harness release function helps
you to safely release from the product.
Cutting attachment
WARNING: Read the warning instructions
that follow before you use the product.
Do the regular maintenance. Let an approved
service center regularly examine the cutting
attachment to do adjustments or repairs.
The performance of the cutting attachment
increases.
The life of the cutting attachment increases.
The risk of accidents decreases.
Only use an approved cutting attachment guard. For
more information, see
Do not use a damaged cutting attachment.
Grass blades and grass cutters
Use the product with an approved grass blade. Do
not use a grass blade without proper installation of
all required parts. Make sure that the installation is
done correctly and that the proper parts are used.
Inproper installation may cause the blade to fly off
and seriously injure the operator or the bystanders.
Wear protective gloves when you handle or do
maintenance on the blade.
881 - 001 - 10.10.2018
Accessories on page 21 .
Use head protection when you operate a product
with a grass blade.
Grass blades and grass cutters are used to cut
rough grass.
A grass blade can cause injury while it continues to
spin after the engine is stopped or the throttle trigger
is released. Make sure that the grass blade has
completely stopped rotating before any
maintenance.
Stop the engine before you do work on the cutting
attachment. Make sure the cutting attachment fully
stops. Disconnect the lead from the spark plug.
Only use an approved cutting attachment or a
correctly sharpened blade.
Keep the teeth of the blade correctly sharpened.
(Fig. 25)
Do not use a damaged cutting attachment.
Attach the transport guard to the grass blade when
you transport or store the product.
Blade thrust
A blade thrust is a sudden movement of the product
to the side, forward or rearward. A blade thrust
occurs when the grass blade or saw blade hits an
object that cannot be cut. In areas where it is not
easy to see the material being cut the risk of blade
thrust increases.
When a blade thrust occurs, there is a risk that the
product or the operator moves out of position. A
blade that moves can hit bystanders and there is a
risk of injuries.
If a blade is bent, has cracks, is broken or damaged,
discard the blade.
Use a sharp blade. The risk of blade thrust increases
when a blade is not sharp.
Fuel safety
WARNING: Read the warning instructions
that follow before you use the product.
Do not mix the fuel indoor or near a heat source.
Do not start the product if there is fuel or engine oil
on the product. Remove the unwanted fuel/oil and let
the product dry. Remove unwanted fuel from the
product.
If you spill fuel on your clothing, change clothing
immediately.
Do not get fuel on your body, it can cause injury. If
you get fuel on your body, use a soap and water to
remove the fuel.
Do not start the engine if you spill oil or fuel on the
product or on your body.
Do not start the product if the engine has a leak.
Examine the engine for leaks regularly.
Be careful with fuel. Fuel is flammable and the fumes
are explosive and can cause injuries or death.
13

Publicité

Table des Matières
loading

Table des Matières