Understanding The Control Board - Cabela's CB24ESC1 Instructions

F/C
F/C

UNDERSTANDING THE CONTROL BOARD

F/C
CONTROL
F/C
F/C Temp
Temp Set
F/C
Temp
Prime Actual
Prime Actual
Prime
P1
F/C
P1 P2
P1
F/C Temp Set
P1 P2
P2
Temp
FC FC
FC
Set
Prime
Actual
F/C
P1 P2
Prime Actual
F/C
P1
FC
Set
Actual
P1
P2
Temp
Temp
P1
Temp Set
Temp Set
FC
Prime Actual
Temp Set
Prime Actual
Prime Actual
Prime Actual
Prime Actual
P2 Temp Set
P2
P2 Prime Actual
Temp Set
P2
F/C
F/C
P2
P1
Prime Actual
Temp Set
P1
FC
P2
Temp Set
Prime Actual
F/C
FC
P1 P2
FC FC
FC
F/C
Set
P1 P2
Actual
FC FC
Prime Actual
FC
Set
P2 Actual
P1
P2 Temp Set
FC
P1
FC
Temp
P2
Prime Actual
FC
Prime Actual
P2
P2
P2
14
F/C
P1
P1
DESCRIPTION
P1 P2
Set
FC FC
Press the Power Button to power on the unit. When connected to a power source, the light below the power
Temp
button will glow blue. Once the Power Button is pressed, the Digital LCD Screen will light up, displaying that it
Set
is ready to operate. Press and hold the button to turn the unit off. Set
Actual
Prime
Actual
P2
The Temperature Switch Button is used to change the temperature readout on the Digital LCD Screen. Press
Temp Set
the button to switch to Celsius (ºC) or to Fahrenheit (ºF), as preferred. Default is set to Fahrenheit. P1
P2
P1
The Digital LCD Screen is used as the information center for your unit. The Digital LCD screen will display your
Set
Desired Temperature Setpoint (SET), Actual Temperature (ACTUAL), Meat Probe Temperature (if connected), and
Actual
P1 P2 Set
any error codes. Temperature can be displayed in either Fahrenheit or Celsius.
Prime Actual
FC FC
Actual
FC
The Adjustment Arrows allow you to increase or decrease your desired temperature (TEMP) on the Control
Set
P2
Actual
Temp
Board. By pressing the UP or DOWN arrows, the temperature changes by 5 degree increments. Press and hold FC
FC
the buttons to increase or decrease the value faster. The temperature can be set to a low 82°C / 180°F, and
Prime
peaks at a high of 260°C /500°F.
P2
P1
Set
The TEMP Button on the Control Board is used in sequence only to make adjustments to the setpoint
Set
P2
temperature. Pressing this button by itself does not result in any change.
The ACTUAL Button on the Control Board is used to display the current (ACTUAL) temperature of the grill. This
temperature readout measures the temperature probe, located inside the main barrel. The Digital LCD Screen
shows the ACTUAL temperature by default.
Press the SET Button on the Control Board to display the desired setpoint (SET) temperature of the grill. After
3 seconds, the display will switch back to the actual (ACT) settings.
Temp Set
TO SET THE TEMPERATURE SETPOINT:
Prime Actual
Temp Set
Prime Actual
1. Press SET.
P2
P2 2. Press TEMP and the temperature readout will begin to flash.
Temp Set
3. Immediately press the UP or DOWN adjustment arrows to set your desired temperature setpoint.
Temp Set
FC
Prime Actual
4. Press TEMP again to lock-in new setpoint, or wait 3 seconds for the TEMP to revert back to ACTUAL.
Temp Set
FC
Prime Actual
P2
NOTE: If there is no action after pressing TEMP, the temperature readout will automatically revert
P2
back to the ACTUAL temperature readout.
Set
Prime Actual
Press and hold the Prime Button to activate an extra feed of pellets to the burn pot. This can be used to add
more fuel to the fire before opening the barrel lid, resulting in a quick heat recovery time. It can also be used
while smoking, to increase the intensity of clean smoke flavor.
The plug-in connection ports on the front of the Control Board are for two Meat Probes. When
a meat probe is connected, the temperature is displayed on the Digital LCD Screen. When not in
use, disconnect the meat probe from the connection port.
P1
Temp
Prime Actual
P1 P2
FC FC
P2
Set
Actual
P1
Temp Set
Temp
Prime Actual
Set
FC
Prime Actual
Actual
P2
P2
FC FC
Temp Set
Prime Actual
Set
Actual
P2
Set
Temp
Prime
Temp Set
FC
Prime Actual
P2
P2
Set
Temp
FC
Prime
P2
Set
Actual
Set
Actual