Table des Matières
Publicité
disclaimers
the mattress support platform shall be ± 3°, which translates to a tolerance of up to 1
½".
The angle (designated "B" in figure 1) between the flat section and foot section for
various configurations of the mattress support platform shall be ± 3°, which translates
to a tolerance of up to ¾".
Any adjustable foundation deemed to be within these allocated tolerances is
considered to have met the manufacturer's quality control standards.
THAT "NEW PRODUCT" SMELL:
Some people notice a slight odor to their new adjustable base—this can come from our
material manufacturing process. This smell is normal and usually disappears before the
product reaches you. Sometimes, however, this smell may still be noticeable. It usually
disappears after a few weeks, providing adequate ventilation of the product and the
environment.
BREAK IN PERIOD:
You can speed up the break-in period by simply spending time in the adjustable bed
through activities such as reading, watching TV or playing with the kids or grandkids.
The extra movement will help the adjustable base respond to weight and temperature
changes. Some of the materials in our adjustable bases such as the woods, metals and
plastics used in the platform, frame and components are sensitive to moisture content
and temperature and may make sounds in colder environments.
PAIRED OPERATION:
When operating a "paired" split base setup there may be a time latency up to 1.5
seconds between each bases articulation.
WEAR AND TEAR:
Wear and tear is damage that naturally and inevitably occurs as a result of normal use
or aging.
FABRIC CARE:
To prolong the life of your fabric, protect from direct sunlight whenever possible.
For spot cleaning, wipe area with a light damp sponge or vacuum with a soft brush
attachment to remove particles. Keep at a minimum of 30cm (12 inches) away from
direct heat sources. For a deeper cleaning, blot liquid spills with a clean dry cloth. Wipe
with a clean cloth dampened with warm water. Do not wet excessively. A soft bristle
brush may be used to remove ingrained soil. Avoid scratching by gentle brushing. Wipe
with a clean cloth dampened with warm water to remove residues. Dry in shade away
from direct heat. If persistent marks remain visible after cleaning, seek professional
advice.
PRODUCT RATINGS:
The lift motors are not designed to operate continuously for more than [2] minutes in
an [18] minute time period or approximately 10% duty cycle. Attempting to circumvent
or exceed this rating will shorten the life expectancy of the product and may void the
warranty. The massage motors are not designed to operate continuously for more than
30 minutes at a time. Please allow the massaging system to rest for 30 minutes after
automatic massage shut off before restarting.
WEIGHT LIMITS:
This product is not rated to support weights exceeding 650 pounds. This product is
not rated to support weights in excess of 650 pounds inclusive of the mattress and
bedding. The base will structurally support this weight, provided it is evenly distributed
across the bed base. The adjustable base is not designed to support or lift this amount
in the head or foot sections alone. Exceeding this weight restriction could damage the
bed and/or cause injury and will void the warranty.
IMPORTANT DO'S AND DON'TS
DO:
•
Plug your adjustable base into a power surge protector.
•
Evenly distribute weight when sleeping in a split setup. Uneven distribution of
weight can cause the base to raise unevenly.
•
Call Customer Service for any technical issues. Do not try to force the base down,
this can damage the motors or frame.
•
Use mild soap and water to clean your adjustable base if staining occurs.
•
Keep in mind that adjustable bases are recommended to be used with adjustable
friendly mattresses
•
Lower to the flat (horizontal) position after use and in between presets.
•
Register your warranty as soon as your adjustable base has been delivered.
DON'T
2
•
Sit on corners/edges of base, this may warp the frame, struts or foam.
•
Tilt the base on its side. This can damage the legs and/or leg screws.
•
Stand or jump on the adjustable base at any time, this can damage the frame and
motors.
•
Drag the base to move it. Dragging the base could damage the frame, strip the
nut/bolts or break the legs. Purchase castors if you plan on moving your base
routinely.
•
Enter and exit the adjustable base with the head and/or foot in the articulated
position. Enter or exit your adjustable in the flat (horizontal) position.
•
Tinker with or modify base. This will void the warranty.
•
Press down on the head or foot while actuated can damage frame and motors.
FCC Certification Statement
This equipment complies with Part 15 of the FCC Rules. Operation of this equipment
is subject to the following two conditions: (1) the equipment may not cause harmful
interference, and (2) the equipment must accept any interference that might cause
undesired operation.
Radio and Television Interference
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy. If the equipment
is not installed and used in accordance with the instructions, the equipment might
cause harmful interference to radio communications. There is no guarantee, however,
that such interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception (which can be determined
by turning the equipment off and on), the user is encouraged to try to correct the
interference by taking one or more of the following measures:
• Relocate the equipment
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that of other
electronics
• Consult the dealer or an experienced radio technician for help.
Important: Any changes or modifications not expressly approved by Serta Simmons
Bedding, LLC ("SSB") could void the EMC compliance and negate your authority to
operate this equipment.
This equipment was tested for FCC compliance under conditions that included the use
of SSB peripheral devices and SSB cables and connectors between system components.
It is important that you use SSB cables and connectors between system components
to reduce the possibility of causing interference to radios, television sets, and other
electronic devices. You can obtain proper SSB cables and connectors through an SSB-
authorized dealer.
Responsible party (contact for FCC matters only) Serta Simmons Bedding, LLC
Corporate Compliance One Concourse Pkwy, Ste. 800
Atlanta, GA 30328
FCC ID: 2AF2O-STS-10 Contains FCC ID: H8N-WLL6540
Industry Canada Statement of Compliance
This device complies with Industry Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
This device complies with ICES-003 Class B specifications of Industry Canada.
IC: 20700-STS10
Contains IC: 1353A-WLL6540
Exposure to Radio Frequency Energy
This equipment complies with FCC radiation exposure limits set forth in the FCC's OET
Bulletin 65 and Industry Canada's RSS-102 standard for an uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20cm
(about 8 inches) between the radiator and your body. This equipment must not be co-
located or operating in conjunction with any other antenna or transmitter.
Publicité
Table des Matières
